background image

2019-2631 

2019-10-10 

 

 
 
 

WARRANTY

 

 

 

The Hayward system carries a limited 3 year warranty 

 

 

1.  3 year warranty on assembly of electrical components and cell 

housing. 

2.  1 year on all electrical items. 

3.  2 years or 15,000 hours, whichever occurs first, pro-rated hourly, 

on titanium electrodes. (Year 1 is warranted fully, thereafter pro- 
rated warranty applies, applicable over the full 2 year period) 

 

• 

Hayward advises that titanium electrodes will have to be replaced every 

15,000 hours of operating time. Under no circumstances shall the 
replacement titanium electrodes exceed the original 15,000 hour warranty. 

 

• 

Hayward warranties will not be honored should it be shown that the 

operating and maintenance procedures have not been followed, 
particularly with regard to the correct maintenance of salt concentration 
and water chemistry. 

 

• 

Hayward warranties of the titanium electrodes will not be honored if the 
system is operated in water temperatures lower than 15°C. 

 

• 

Hayward warranties of the titanium electrodes will not be honored if the 

system is operated in water where the salt concentration is lower than 
3000 ppm. 

 

• 

During the warranty period the customer shall return the defective 
component, freight prepaid, accompanied by the original invoice or proof 
of purchase, and Hayward shall at its sole discretion elect to repair or 
replace the defective component and return it to the customer, freight pre- 
paid. 

 

 

Hayward accepts no responsibility other than to repair or replace a defective 
component, and this warranty specifically excludes product failure due to accidental 
damage, abuse, misuse, negligence, damage due to non-compliance of the operating 
manual or unauthorized alterations or modifications to the system. Hayward accepts 
no responsibility and is not liable for any extended warranties or variations to this 
warranty offered by re-sellers of Hayward systems. 

Summary of Contents for Saline C® 6.0




















Reviews: