background image

07/21 

      Model 1117LNHO/1117LNHO2 

Page 2 of 7 

 

 
 
 
 
 

 
 
 

 

RECOMMENDED TOOLS

: Hack saw, pipe joint sealant, screwdriver, level, 12" adjustable 

wrench, 10" pipe wrench, 5/64

“ hex key wrench, 9/16”, 1/2", 7/16” socket wrench or open-end 

wrench.

 

LOCATION OF UNIT:

 The Model 1117LNHO/1117LNHO2 Drinking Fountain is a wheelchair 

accessible drinking facility. The height dimensions shown, meet current ADA requirements. 
When installing this unit, local, state or federal codes should be adhered to. If height other 
than shown is required, then dimensions must be adjusted accordingly. 

SUPPLY LINE

: The minimum recommended line size 

is 1/2“IPS with 30-90 psi (2-6 ATM) 

flowing pressure. Where sediment or mineral content is a problem, an inlet filter is 
recommended. 

PLUMBING CONNECTIONS:

 

Inlet is 3/8” O.D. push-in type fitting. Waste outlet is female 1-

1/4

” NPT. 

ELECTRICAL CONNECTIONS

Drinking Fountain may be mounted on external wall of 

building provided transformer shall be mounted inside the wall and protected from 
water as shown on RKHO Series O&M details (page 8) per NEC/CEC and local code.

 

  Sensor(s)

      

1117LNHO with 1RKHO.H:  100-277VAC x 9VDC, 50-60Hz, 5 Watts.      

      1117LNHO2 with 2RKHO.H:  100-277VAC x 9VDC, 50-60Hz, 5 Watts.       

MAINTENANCE: 

Periodically clean out the supply line Y-strainer (and strainer located inside 

push button valve on Model 1117LNHO). Refer to 5874 Series Valve Manual for more 
information. 

 

INSTALLATION PROCEDURE

 

 

GENERAL NOTES: 

1.  For all plastic push-in type fitting connections, only connect NSF-61 copper or 

plastic tubing.  Stainless steel or glass tubing is not recommended.  The 
following assembly instructions must be followed to ensure a watertight 
connection: 

a.  Cut tubing square and clean. 
b.  Mark from end of tube the length of insertion (See table below). 
c.  Push tube into the fitting until it bottoms out. 
d.  To remove, depress collet and pull tubing out. 

 

Tube Sizes 

O.D. 

Tolerance 

Insertion Depth 

3/8” 

±.005” 

3/4” 

 
 
 
 

SHOULD YOU EXPERIENCE DIFFICULTY WITH THE INSTALLATION OF THIS 
MODEL PLEASE CALL: 

 

      

TECHNICAL SUPPORT:

 

1-800-766-5612 

FOR CUSTOMER SERVICE:    

1-888-640-4297 

Summary of Contents for 1117LNHO








Reviews: