manualshive.com logo in svg

Hawk Centurion CGR Series, Manual

Share
Download
Hawk Centurion CGR Series Manual Download Page 12

Setup Procedure

12

Centurion

 

Guided Radar

Setting Advanced Parameters

The 

Advanced

 menu parameters are for adjusting primary Sensitivity, echo controls/filters, communications 

and output settings.

2. Advanced Parameters

Parameter

Description

 

Options

Comms

Adjust communication protocol settings.

• Device ID
• Baud Rate

Digitize

Perform auto-Digitization of Sensitivity based on mounting and 
Dielectric of material touching the probe (see Setup Procedure A)

• Execute
• Disable
• Cancel

Sensitivity

Manual adjustment of Sensitivity. This value will also be 
automatically adjusted by other calibration  routines. Sensitivity is 
the primary adjustment for the units ability to detect media

• 0-100

Blanking

Blanking is a non-measurable zone. This can be increased to 
‘Blank’ out high level false echoes caused by mounting

• Adjustable

Cal Mount

Performs a digital mapping routine of a user selected span. Used 
when there is signal interference at high level or mounting. 

Use Digit Bias to adjust bias (cal sensitivity) of mapping range

• Cal Start 
• Cal End

Analogue

Adjust and tune 4-20mA settings

• 4-20
• 20-4
• 4mA tuning
• 20mA tuning
• Park 4mA
• Park 8mA
• Park 12mA

Factry Reset

Restore unit to factory defaults

• Yes
• No

Device Info

Display device information

Lock Code

Adjust the peak Sensitivity cap. This value will be automatically 
adjusted by other calibration routines

• Disable
• Enable

Summary of Contents for Centurion CGR Series





















Reviews:

No comments

Brands by name

Popular brands

Load more brands