PREPARATION
WORK PREPARATION
• Wear proper apparel. Do not wear loose clothing, gloves,
neckties, rings, bracelets or other jewelry which may get
caught in moving parts of the machine.
• Wear protective hair covering to contain long hair.
• Wear safety shoes with non-slip soles.
• Wear safety glasses complying with United States ANSI
Z87.1. Everyday glasses have only impact resistant
lenses. They are NOT safety glasses.
• Wear face mask or dust mask if operation is dusty.
• Be alert and think clearly. Never operate power tools
when tired, intoxicated or when taking medications that
cause drowsiness.
WORK AREA PREPARATION
• Keep work area clean. Cluttered work areas invite
accidents.
• Do not use power tools in dangerous environments.
• Do not use power tools in damp or wet locations.
• Do not expose power tools to rain.
• Work area should be properly lighted.
• Keep visitors at a safe distance from work area.
• Keep children out of workplace. Make workshop
childproof.
• Use padlocks, master switches or remove switch keys
to prevent any unintentional use of power tools.
• Keep power cords from coming in contact with sharp
objects, oil, grease, and hot surfaces.
TOOL MAINTENANCE
• Always unplug tool prior to inspection.
• Consult manual for specific maintaining and adjusting
procedures.
• Keep tool lubricated and clean for safest operation.
• Keep all parts in working order. Check to determine that
the guard or other parts will operate properly and
perform their intended function.
• Check for damaged parts. Check for alignment of
moving parts, binding, breakage, mounting and any
other condition that may affect a tool’s operation.
• A guard or other part that is damaged should be
properly repaired or replaced. Do not perform
makeshift repairs. (Use parts list provided to order
replacement parts.)
• Never adjust attachments while tool is running. Turn
tool off and unplug from power source to avoid
accidental start-up.
• Have damaged or worn power cords replaced
immediately. Keep cutting tools sharp for efficient and
safest operation.
TOOL OPERATION
• Use right tool for the job. Do not force tool or attachment
to do a job for which it was not designed.
• Disconnect tool before changing attachments.
• Avoid accidental start-up. Make sure that the tool is in
the “OFF” position before plugging in, turning on safety
disconnect or activating breakers.
• Do not force tool. It will work most efficiently at the rate
for which it was designed.
• Keep hands away from chuck, centers and other moving
parts.
• Never leave tool running unattended. Turn the power off
and do not leave tool until it comes to a complete stop.
• Do not overreach. Keep proper footing and balance.
• Never stand or lean on tool. Serious injury could occur if
tool is tipped or if centers are unintentionally contacted.
• Know your tool. Learn the tool’s operation, application
and specific limitations.
• Handle workpiece correctly. Mount firmly in holding
devices. Protect hands from possible injury.
• Turn machine off if workpiece splits or becomes loose.
• Use cutting tools as recommended in “Operation” of this
manual.
For your own safety do not operate your wood lathe until
it is completely assembled and installed according to
instructions.
PROTECTION: EYES, HANDS, FACE, BODY,
EARS
• If any part of your lathe is missing, malfunctioning, or
has been damaged or broken, cease operating
immediately until the particular part is properly repaired
or replaced.
• Wear safety goggles that comply with United States
ANSI Z87.1 and a face shield or dust mask if operation
is dusty. Wear ear plugs or muffs during extended
periods of operation.
• Small loose pieces of wood or other objects that
contact a spinning workpiece can be propelled at very
high speed. This can be avoided by keeping the lathe
clean.
• Never turn the lathe ON before clearing all tools and
scraps from the bed, head and tailstock. Only the
related support devices for the operation planned should
be present.
• Never place your face or body in line with the chuck or
faceplate.
• Never place your fingers or hands in the path of cutting
tools.
• Never reach in back of the workpiece with either hand to
support the piece, remove wood scraps, or for any other
reason. Avoid awkward operations and hand positions
where a sudden slip could cause fingers or hand to
move into a spinning workpiece.
16
WARNING