Haug Pack-Vac Instruction Manual Download

Page: 10 / 12

Page 10 of 12

Haug Quality Equipment

2530 Wrondel Way



: 775-455-4249

www.haugquality.com

Reno, NV 89502

[email protected]

Maintenance

The Pack-

Vac™ requires little maintenance. The following guidelines will ensure years of service from

your Pack-

Vac™

7.1

Cleaning

The Pack-

Vac™ tank should be cleaned on a regular basis with mild soap and water to remove mineral

deposits before they degrade the clarity of the plastic. Using water with lower mineral content will delay
mineral build-up. Commercially available plastic polishers and cleaners by Novus can be used. Availa-
ble from www.mcmaster.com

7.2

Gasket installation

Remove old gasket.

The lip of the gasket faces out!

Start at the back center and press the ends together into the groove.

Next, press each corner into the groove. Do not stretch the gasket.

Summary of Contents for Pack-Vac













Search results

Summary of Contents for Pack-Vac

Reviews:

Related manuals for Pack-Vac

Brands by name

Popular brands

Haug Pack-Vac, Instruction Manual

Search results

Summary of Contents for Pack-Vac

Reviews:

Related manuals for Pack-Vac

Brands by name

Popular brands