background image

T

 +44 (0)1709 377172     

F

 +44 (0)1709 377173

14

CLEANING & CARE

BUMPER COVER 

During general use, the bumper cover can be cleaned by wiping with a mild detergent 
solution.  

Where necessary the cover can be laundered or wiped clean. Where there is staining or 
body fluids on the outer cover, wash thoroughly with soap and water, then wipe with a 

sodium hypochlorite solution diluted to 1000ppm before laundering. Bumper covers may be 
laundered if the foam can be removed.

WARNING

Eye protection, gloves, and protective clothing should be worn when carrying out cleaning 
and disinfection procedures. 

When disinfecting the system, Harvest Healthcare recommends the following guidelines 

which have been developed to comply with recognised infection control procedures. 
These procedures are also to be used to prevent cross infection when transferring the 
system between patients. 

INSTRUCTIONS ON HOW TO LAUNDER THE OUTER COVER

 

Lay the bumper cover down on a flat surface and unzip the pocket to gain access to the 

internal foam padding. Remove the foam padding. The bumper can now be laundered. 
1 Pre wash cold 10 minutes  
2 Main wash 80°C 10 minutes  

3 Followed by cold rinses and extraction. 

 

Do not use abrasive cleaners, phenol disinfectants, solvents, or alcohol-based cleansers, 
e.g. Dettol, Phenicol, Hibiscrub, Clearsol, Stericol, Hycoline, as these will damage the cover 
materials. 
Tumble dry at low heat. 
Do not iron.  
Ensure that the cover is thoroughly dried before inserting the foam and placing the bumper 
into storage. 

HYPERCARBONATE AND PHENOL-BASED SOLUTIONS SHOULD NOT 
BE USED AS THESE WILL DAMAGE THE PRODUCT COVER

DISPOSAL

If contaminated, please dispose of as clinical waste.
If not contaminated dispose of as household waste at your local approved facility.

Note: 

•  Remove the foam before decontamination.
•  Harvest Healthcare recommends using a wash bag to protect the system if 
decontaminating in a washing machine.
•  Carry out a risk assessment to ensure the bumper is suitable for the users’ requirements.
•  In the event of the bumper system becoming damaged discontinue use immediately and 
contact Harvest Healthcare for advice. 
•  If you have any questions, please contact Harvest Healthcare before use. 

Summary of Contents for BUMPERS

















Reviews: