20 99 000 1035 9900
Adjustment of crimp depth
Crimp depth to be adjusted as follows:
Adjusting screw to be turned
clockwise for reducing the crimp depth
and
anti-clockwise for increasing the crimp depth
Adjustment tolerances:
-
1 scale spacing on the screw = adjustment by 0.01 mm
-
1 full rotation of screw
= adjustment by 0.2 mm (indication on the screw
as well as on the rough scale)
-
5 rotations of the screw
= adjustment by 1 mm (indication on the rough scale)
crimp depth -
adjusting screw with 0.01 mm tolerance
crimp depth +
rough scale indicating 0.2 mm tolerances
Control of crimp depth
Crimp tool adjustment is done in the factory, but under permanent use periodic gauging is
recommended to insure accurate calibration. This is easily accomplished with a gauge ø 2.0 mm as
follows:
A crimp depth of 2.0 mm is set by means of the adjusting screw (scale mark at "2", screw mark at "0"
as shown in the fig. above) and the tool is to close. After insertion of gauge, it must be just enough
space for moving the gauge inside the entry hole. If the indenter closure is too small or too large to
exactly match the gauge, the deviation (+/-) can be checked by the precision setting of the screw. In
case the deviation exceeds the tolerances requested by the contact manufacturer, please contact the
latter.
Setting paramenters (reference table)
Contact type
Art.-No.
Locator
position
Crimp depth setting
POF pin contact 1mm/2.2mm POF for Han DD, Han K
2010 001 3211
1
1.48 mm
POF pin contact 1mm/2.2mm POF for Han D, Han U
2010 001 3212
1
1.48 mm
POF pin contact 1mm/2.2mm POF for Han E
2010 001 3311
1
1.48 mm
2010 001 3213
1
1.48 mm
POF bush contact 1mm/2.2mm POF for Han DD, Han K
2010 001 3221
2
1.48 mm
POF bush contact 1mm/2.2mm POF for Han D, Han U
2010 001 3222
2
1.48 mm
POF bush contact 1mm/2.2mm POF for Han E
2010 001 3321
2
1.48 mm
POF end sleeve 1mm/2.2mm POF
2010 001 3232
3
1.8 mm
POF pin contact 1mm/2.2mm POF for Han multi contact module
2010 001 4211
3
1.8 mm
POF bush contact 1mm/2.2mm POF for Han multi contact module 2010 001 4221
3
1.8 mm
FH ST plug connector 1mm/2.2mm POF
2010 001 2211
3
2.0 mm
F-SMA plug connector 1mm
2010 001 1211
3
2.0 mm
F-SMA plug connector 1mm
2010 001 1221
3
2.0 mm
F-SMA plug connector 1mm
2010 001 1223
3
2.0 mm
F-SMA plug connector 1mm
2010 001 1241
3
2.0 mm
F-SMA plug connector 1mm
2010 001 1243
3
2.0 mm
Maintenance and repair
Keep the tool clean and properly stored when not in service. The joints need to be oiled regularly and
the circlips securing the bolts have to be always in place.
For repair, please send the tool back to the manufacturer.
HARTING Electric GmbH & Co. KG
Wilhelm-Harting-Str. 1; D-32339 Espelkamp
Telefon +49-5772 47-97100, Telefax +49-5772 47-124
Internet: http://www.Harting.com; e-mail: [email protected]
