Harsco Industrial P-K DURATION II D2DW-30(S/D) Installation & Owner'S Manual Download Page 7

 

P-K DURATION II 

™ Indirect Domestic Water Heating System 

 

2.5.4 

Chemical Hazards 

• 

Chemical hazards from cleaning products.  Use caution when cleaning the system.  
The use of professional assistance is recommended.  Use safe procedures for the 
disposal of all cleaning solutions. 

 

 

2.5.5 

Pressure Hazards   

 

 

Pressure hazard!  Hot fluids.  Isolation valves are provided on all inlets and outlets for 
your convenience.  Make sure all isolation valves are closed before servicing.   

 

Pressure hazard!  Hot fluids.  Annually test safety relief valve for proper operation.  
Do not operate with faulty relief valve(s).  

 

2.5.6 

Slip, Fall Hazards  

 

Tripping hazard!  Do not install piping on floor surfaces.  Maintain clear path around 
the P-K DURATION II

™ system.  

 

Slip and fall hazard!  Use drip pan to catch water while draining.  Maintain dry floor 
surfaces.  

 

Fall hazard!  Do not stand on the P-K DURATION II

™ system.   

3  INSTALLATION  

 

Installation and service must be performed by a qualified installer, service agency, 

or gas supplier.

 

 

3.1 

R

ECEIVING AND 

S

TORAGE

 

3.1.1 

Initial Inspection 

Upon receiving the  P-K Duration II system, inspect it for signs of shipping damage.

  Since some damage 

may  be  hidden,  unpack  the  product,  open  the  front,  and  side  doors  to  inspect.    Verify  that  the  total  number  of 
pieces shown on the packing slip agrees with those actually received. 

NOTICE!  Note any damage, suspected potential damage, or shortage of materials on the freight bill and 
immediately notify the carrier.  File all claims for shortage or damage with the carrier.  Claims for hidden damages 
must be filed with your carrier within 7 days.

 

3.1.2 

Storage Prior to Installation 

If the P-K Duration II system is not installed immediately, it must be stored in a location adequately protected from 
the  weather,  preferably  indoors.    If  this  is  not  possible,  then  it  should  remain  in  the  shipping  container  and  be 
covered by a tarpaulin or other waterproof covering. 

NOTICE!  Controls and other equipment that are damaged or fail due to weather exposure are not covered by 
warranty. 

General Warning

General Warning

General Warning

Summary of Contents for P-K DURATION II D2DW-30(S/D)





























Reviews: