manualshive.com logo in svg

Harris NEXIO AMP Generation 6, Hardware Installation And User'S Manual

Share
Download
Harris NEXIO AMP Generation 6 Hardware Installation And User'S Manual Download Page 34

Chapter 3

System Installation

34

175-100423-00

To Rack Mount NXAMP3801HDX/HDI

Ensure that the rack is anchored to the floor so that it cannot tip over when
NXAMP3801HDX/HDI is extended out of the rack.

Figure 3-1

Rack Mounting

1

Remove the slides from the rails.

2

Attach a slide to each side of the NXAMP3801HDX/HDI chassis using seven screws per side.

Make sure the release latch is located at the back of the chassis.

3

Attach an extension to the back of each rail to match the depth of your rack.

4

Attach the rails to the rack posts.

5

Pull the inner rail out until it locks.

6

Slide the NXAMP3801HDX/HDI into the rail until it stops; press the release latch on each slide and

continue to slide the NXAMP3801HDX/HDI into the inner rail all the way into the rack.

To Remove NXAMP3801HDX/HDI from a rack

1

Stand in front of the NXAMP3801HDX/HDI and pull the NXAMP3801HDX/HDI out until it locks in place.

2

Press the release button on the outside of each inner rail, and pull the NXAMP3801HDX/HDI out of the

rack.

Summary of Contents for NEXIO AMP Generation 6













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands