background image

P/N: 76015 RevE 72618

SL600 • Pinnacle Stair Lift Installation Manual

 19

Pinnacle Stair Lift

FOLDING RAIL INSTALLATION

12. Reinstall the two plastic caps on the feet to 
cover the threads. 

[Figure 19-1]

13. Carefully move the fork with your hand to make 
sure it operates smoothly. Allow it to go all the way to 
the floor. Confirm that both feet sit level on the floor 
and the hinge-joint is fully straight. 

[Figure 19-2]

Figure 19-2

Figure 19-1

14. Install the folding rail parts onto the Pinnacle 
chassis. Shown here is just a bare Pinnacle chassis to 
make the pictures more clear. 

[Figure 19-3]

First, with a 5/16

"

 Allen wrench, remove the two 

large cap screws from the wall-side of the unit, then 
install the folding rail side-plate, but don't tighten 
them yet.

15. Install the #8 screw, then tighten it and the 
two Allen head bolts. If your Pinnacle stair lift is 
still installed on the track, you'll have to use a short 
wrench and maybe a right-angle screwdriver. 

[Figure 

19-4]

16. Ensure the folding rail sensor is on the bottom 
safety obstruction panel.

 [Figure 19-5]

17. Follow the normal procedure for installing rail 
brackets and tightening them. This procedure is 
detailed on pages 5 & 6 (steps 7 & 8). 

18. Test ride the unit a couple of times to verify that 
the folding rail is operating properly. 

WARNING

Be careful not to pinch your fingers 

when moving the fork.

Figure 19-3

Figure 19-4

Figure 19-5

NOTE

 - 

When you test run the chassis, ensure 

the roller enters the fork and not above or below, 
causing damage.

Summary of Contents for SL600FR-LH





















Reviews:

Related manuals for SL600FR-LH