Harmar Mobility Pinnacle SL600 Installation And Service Manual Download Page 16 | Manualshive

Page: 16 / 27

background image

16 Pinnacle Stair Lift manual | | www.Harmar.com | 866-351-2776

table of Contents

V. FOLDING RAIL INSTALLATION

A. RAIL INSTALLATION PREPARATION

TOOLS REQUIRED

The following is a suggested list of basic tools to have on hand during installation.

Wrenches

High torque drill

Allen wrenches (standard SAE set)

Carpenter’s square

Pencil

Tape measure

INCLUDED PARTS

Before beginning folding rail installation, please inspect and check the box contents. Please note that the Pinnacle
Parts Box is omitted on new units since these parts are factory installed on the stair lift. Report any damage to
Harmar or the freight carrier.

Rail Box:

• Assembled Folding Rail

Track Bracket Box:

• Two (or more) assembled short track brackets, rack pieces, two adjustable feet

Pinnacle Parts Box:

• Folding track side-plate

• Screw

• Modified front and rear Pinnacle safety switch bumpers. For new units, this box is

omitted and these parts are already installed on the stair lift.

folding rail installation

te!

«
...
14
15
16
17
18
...
»

Summary of Contents for Pinnacle SL600




























Reviews:

No comments

Related manuals for Pinnacle SL600

Brand: Alber Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands