background image

SL300 PINNACLE STAIRLIFT:

 

Install Manual

26MAY2022  |   630-00100 J

5

INTRODUCTION

PINNACLE STAIRLIFT: SECTION 2

SECTION 2

INTRODUCTION

DEVICE NAME:  

PINNACLE SL300 SERIES

Indications of Use: The Harmar Pinnacle SL300 is to 

assist the transfer of patients or mobility impaired 

persons up and down levels of a residence. 

READ AND UNDERSTAND

This manual provides instructions for proper 

installation and maintenance of the SL300 stairlift. 

Please refer to the owner’s manual for operating 

instructions. Any alterations to the equipment 

without written authorization by the manufacturer 

is prohibited and will void the warranty.

WARRANTY

Please ensure that you advise the owner of the 

Pinnacle SL300 stairlift to fill out the separate 

warranty form and return it within ten (10) days of 

purchase to register the lift.

TECHNICAL 

SPECIFICATIONS

Visit harmar.com for specifications on the lift model.

CODE STATEMENT

Code requirements for SL300 may vary depending 

on location. It is the installer’s responsibility to 

contact their state, city or local code enforcement 

office and determine all the regulations the lift and 

installation are subject to. This must be done before 

installing the SL300. Intertek (ETL) Certified to ASME 

A18.1-2017 section 7.

Summary of Contents for Pinnacle SL300

























Reviews: