Programming
55
Modero G4 Touch Panels - Configuration & Programming Manual
Page Commands (Cont.)
@PPK
Kill a specific popup page from all pages. Kill refers to the deactivating (Off) of a popup window from all pages. If the pop-up page
is part of a group, the whole group is deactivated. This command works in the same way as the 'Clear Group' command in
TPDesign 4.
•
Syntax
:
"'@PPK-<popup page name>'"
•
Variable
:
popup page name = 1 - 50 ASCII characters. Name of the popup page.
•
Example
:
SEND_COMMAND Panel,"'@PPK-Popup1'"
Kills the popup page ’Popup1’ on all pages.
@PPM
Set the modality of a specific popup page to Modal or NonModal. A Modal popup page, when active, only allows you to use the
buttons and features on that popup page. All other buttons on the panel page are inactivated.
•
Syntax
:
"'@PPM-<popup page name>;<mode>'"
•
Variables
:
popup page name = 1 - 50 ASCII characters. Name of the popup page.
mode = NONMODAL converts a previously Modal popup page to a NonModal.
MODAL converts a previously NonModal popup page to Modal.
modal = 1 and non-modal = 0
•
Example 1
:
SEND_COMMAND Panel,"'@PPM-Popup1;Modal'"
Sets the popup page ’Popup1’ to Modal.
•
Example 2
:
SEND_COMMAND Panel,"'@PPM-Popup1;1'"
Sets the popup page ’Popup1’ to Modal.
@PPN
Activate a specific popup page to launch on either a specified page or the current page.
If the page name is empty, the current
page is used (see example 2).
If the popup page is already on, do not re-draw it. This command works in the same way as the
’Show Popup’ command in TPDesign4.
•
Syntax
:
"'@PPN-<popup page name>;<page name>'"
•
Variables
:
popup page name = 1 - 50 ASCII characters. Name of the popup page.
page name = 1 - 50 ASCII characters. Name of the page the popup is displayed On.
•
Example 1
:
SEND_COMMAND Panel,"'@PPN-Popup1;Main'"
Activates ’Popup1’ on the ’Main’ page.
•
Example 2
:
SEND_COMMAND Panel,"'@PPN-Popup1'"
Activates the popup page ’Popup1’ on the current page.
@PPT
Set a specific popup page to timeout within a specified time. If timeout is empty, popup page will clear the timeout.
•
Syntax
:
"'@PPT-<popup page name>;<timeout>'"
•
Variables
:
popup page name = 1 - 50 ASCII characters. Name of the popup page.
timeout = Timeout duration in 1/10ths of a second.
•
Example
:
SEND_COMMAND Panel,"'@PPT-Popup1;30'"
Sets the popup page ’Popup1’ to timeout within 3 seconds.
@PPX
Close all popups on all pages. This command works in the same way as the 'Clear All' command in TPDesign 4.
•
Syntax
:
"'@PPX'"
•
Example
:
SEND_COMMAND Panel,"'@PPX'"
Close all popups on all pages.
@PSE
Set the show effect for the specified popup page to the named show effect.
•
Syntax
:
"'@PSE-<popup page name>;<show effect name>'"
•
Variables
:
popup page name = 1 - 50 ASCII characters. Name of the page the popup is displayed On.
show effect name = Refers to the popup effect name being used.
•
Example
:
SEND_COMMAND Panel,"'@PSE-Popup1;Slide from Left'"
Sets the Popup1 show effect name to ’Slide from Left’.
