SB26
Operation
10
•
Dolby® Digital
: If a dolby digital audio stream is sensed by the soundbar,
the OSd will indicate that the dolby digital decoding is active.
•
Bluetooth
: the following information is displayed in the OSd during
Bluetooth operation:
•
Bluetooth pairing - when the SB26 is in pairing mode
•
Bluetooth connected - when the connection to a new device is
successful
•
Bluetooth - when the source Bluetooth is operated
In addition to the status information, the OSd will also display messages if the selected
hdMI connection cannot be detected or if the video signal is lost.
Operating through Bluetooth®
to wirelessly stream audio to the SB26 from a Bluetooth-enabled device:
1. confirm that the SB26 is in the Bluetooth pairing mode (the Bluetooth
button led will be flashing blue). If the led is not flashing blue, press and
hold the Bluetooth button until its led starts flashing blue.
the OSd will display
Bluetooth pairing
.
2. Place the device in the pairing mode.
3. use the device’s Bluetooth pairing menu to pair it with the SB26. the
system will appear as SB26 in the list of Bluetooth available devices. when
the SB26’s Bluetooth button led illuminates constantly, it is paired with the
device and you can stream audio via Bluetooth from the device to the SB26.
the OSd will display
Bluetooth connected
.
to listen to audio from the Bluetooth device, press the Bluetooth source button on the
SB26 to activate the source. If the SB26 is in Standby mode, you can automatically wake
up the system by starting to stream an audio Bluetooth signal to the SB26 as long as
your device has already been paired with the SB26. the OSd will display
Bluetooth
.
to disconnect the Bluetooth device, press and hold the SB26’s Bluetooth button until
the led begins flashing. the OSd will display
Bluetooth pairing
.
NOTE:
•
You can manually switch sources to the paired Bluetooth device by
pressing the SB26’s Bluetooth button.
•
If you switch the SB26 to a different source while a paired
Bluetooth device is streaming to the system, the SB26 will send a
STOP command and the Bluetooth device will stop streaming.
•
While pairing the Bluetooth device for the first time, it may reset
the volume level to maximum.
Switching Sources
the remote has individual selector buttons for each source except Bluetooth. the active
source’s Source Indicator led will illuminate upon selection.
Adjusting the System’s Volume
Soundbar
Press the SB26’s Volume up and down buttons on the remote control or on the soundbar
to raise and lower the system’s volume, one press at a time. hold down the button to
raise or lower the volume continuously.
NOTE: The lowest setting of the Volume Down button will mute the system.
For the best sound, we recommend turning your tV’s built-in speakers off. consult
your tV’s owner’s manual to find out how to do this. If there is no way to turn your tV’s
speakers off, you can adjust the tV’s volume so that your SB26 system will always supply
most of the sound:
1. using the volume buttons on your tV, turn its volume all the way down.
2. use the SB26’s
Volume Up/Down
buttons to set the sound to a comfortable
listening level.
this way, your SB26 system should always be louder than your tV speakers.
NOTE: If you play the SB26 at more than 50% of max volume and turn the
SB26 off using the Power button, the system will automatically reset at 50%
of the max volume.
Subwoofer
Press the remote control subwoofer volume up and down to raise and lower the system’s
subwoofer volume.
Subwoofer Volume Control
use the subwoofer’s volume control to balance the bass with the rest of the sound. Play
music or movies that you are familiar with and adjust the subwoofer’s Volume knob
so the bass sounds are balanced on both music and films. listen to several different
music recordings and film soundtracks that contain strong bass, and find a setting for
the Volume knob that does not over-emphasize the bass or make it sound weak.
Bluetooth
Volume
