background image

Direct Connection of the 12-Volt Power Harness With 
In-Line Fuse Holder

Use this method when you want a direct connection to the
vehicle’s electrical system. Leaving the in-line fuse holder intact,
cut the cigarette lighter plug from the cord and strip about 
4 inches of the thick, black insulation away from the three wires
inside. 

Connect the red wire inside to the vehicle’s ACC (accessory 
circuit). Connect the yellow wire to the vehicle’s constant 12V
power wire, and connect the black wire to the vehicle’s ground
circuit. The best place to make those connections is in the harness
that provides power and ground to the vehicle’s radio. 

IMPORTANT: Replace the in-line fuse only with one of the 
same type and rating.

INSTALLATION  5

INSTALLATION

Auxiliary 

Device

(optional)

Third-Party

CD Changer

Interface

(optional)

Text Display

Back

Side

+12V = yellow

CD Changer L/R In

Aux. L/R In

Antenna In

2A Fuse

2A Fuse

Cut and
Strip Cable

ACC = red

GND = black

Electronics Enclosure

Antenna Cable
(disconnect from 
Head Unit/Radio)

Head Unit/Radio

or

or

or

or

Cell Phone,

Satellite Radio, etc.

iPod Cable

3.5mm Stereo Cable

(not included)

Line Out Cable

Wired

FM Adapter

Wireless

FM Transmitter

(Only available in 

selected countries)

12-Volt
Accessory
Power Cable

iPod

Control Knob

Direct Power

Connection

Removable

Power Connection

 

Wiring Diagram

Tip = LEFT

Sleeve = GROUND

3.5mm Stereo 

Mini-Plug Cable

RIGHT = Ring

Audio Input/Output Jacks

Summary of Contents for DRIVE + PLAY [HK-DP1EU]













Reviews: