17
Check
( ) ( )
Yellow to V5-9
(
NS
)
.
(
3
)
( ) ( )
Green to V5-8
(
NS
)
.
(
2
)
( ) ( )
Gray to P4-6
(
S
)
.
(
63
)
( ) ( )
Violet to P4-5
(
S
)
.
(
64
)
( ) ( )
Gray to P4-3
(
S
)
.
(
59
)
( ) ( )
White to P4-2
(
S
)
.
(
58
)
( ) ( )
Gray to P3-6
(
S
)
.
(
51
)
( ) ( )
Violet to P3-5
(
S
)
.
(
52
)
( ) ( )
White to P3-2
(
S
)
.
(
50
)
( ) ( )
Connect blue wire from harness
(
62
)
to S-4R
(
S
)
.
( ) ( )
Connect yellow wire
(
61
)
to S-5R
(
S
)
.
( ) ( )
Connect red wire
(
57
)
to S-2R
(
S
)
.
( ) ( )
Connect green wire
(
56
)
to S-3R
(
S
)
.
( ) ( )
Mount power transformer
(
PT1
)
into center hole,
inserting flat washers
(
Figure K
)
on studs
between transformer and chassis. Use #10 nuts,
lockwasher under nut. NOTE: Be careful not to
pinch wires. Slip cardboard protective covers over
transformers to prevent scratches during
assembly.
( ) ( )
Mount output transformers OT1 and OT2 in
same manner. Use flat washers and #10 nuts,
lockwasher under nut. Use protective covers.
( ) ( )
Bend up fuse side tab F2 on fuse holder.
( ) ( )
Connect black wire from power transformer to
fuse holder F2
(
S
)
.
( ) ( )
Connect black/white wire to AC-2
(
NS
)
. Slip
large rubber grommet over all remaining leads
coming from power transformer. See Pictorial #6.
( ) ( )
Connect green-white lead to V8-G2
(
S
)
.
( ) ( )
Connect green/red lead to V8-7
(
S
)
.
( ) ( )
Connect green lead to V8-2
(
S
)
.
( ) ( )
Connect brown-white lead to V9-G1
(
S
)
.
( ) ( )
Connect brown/blue lead to V9-2
(
S
)
.
( ) ( )
Connect brown lead to V9-7
(
S
)
.
The red and white leads of the power transformer will be wired after the electrolytic bracket is installed.
( ) ( )
Cut one end of 15 ohm 1 watt 5% resistor
(
brown-green-black-gold
)
to
½
˝ and connect to V8-8
(
S
)
.
( ) ( )
Cut the other end
½
˝ and connect to V8-X3
(
S
)
. Dress resistor body so that it overhangs socket and
clears pins 1 and 2.
In the same manner, connect the following:
( ) ( )
15 ohm 1 watt 5% resistor
(
brown-green-black-gold
)
from V7-8
(
S
)
to V7-X4
(
S
)
.
( ) ( )
15 ohm 1 watt 5% resistor
(
brown-green-black-gold
)
from V9-8
(
S
)
to V9-X2
(
S
)
.
( ) ( )
15 ohm 1 watt 5% resistor
(
brown-green-black-gold
)
from V10-8
(
S
)
to V10-X1
(
S
)
.
