Harman Kardon AVR 347 Service Manual Download Page 15

Page: 15 / 218

CONNECTIONS

Audio Connections

There are two formats for audio connections: digital and analog. Digital
audio signals are of higher quality, and are required for listening to
sources encoded with digital surround modes, such as Dolby Digital and
DTS. There are three types of digital audio connections: HDMI, coaxial
and optical. Any one type of digital audio connection may be used for
each source device, but never more than one for the same source.
However, it’s okay to make both analog and digital audio connections
at the same time to the same source.

NOTE:

Since the AVR 347 is capable of processing the audio

and video portions of most HDMI signals, if your video display
device has an HDMI input, you may make a single HDMI
connection from your HDMI 1.1-or-higher source device (such
as a DVD player) to the AVR. In that case, no separate digital
audio connection is required. Make sure to turn the volume on
your television all the way off.

Digital Audio

The AVR 347 is equipped with two HDMI (High-Definition Multimedia
Interface) inputs, and one output. HDMI is capable of carrying digital
audio and video information using a single cable, thus delivering the
highest possible quality picture and sound.

The AVR 347 is Simplay HD-verified for compatibility via the HDMI
connection with other Simplay HD-verified products.

There are different versions of HDMI, depending on the capability of the
source device and the type of signal it is capable of transmitting via the
HDMI connection.

In addition, receivers and processors such as the AVR 347 may handle
the incoming signal in several different ways, depending on their capability
as well. Thanks to its powerful processor, the AVR 347 is capable of
processing both the audio and video components of the HDMI data,
minimizing the number of cable connections in your system.

NOTE:

Some multichannel audio devices, such as DVD-Audio,

SACD, HD-DVD or Blu-ray Disc players, output some audio
formats only through the source’s multichannel analog outputs.
These include DVD-Audio players with HDMI version 1.0, and
HD-DVD and Blu-ray Disc players that do not decode the digital
audio. In those cases, make a separate analog audio connection
in addition to the HDMI connection, which is still used for video
or if you wish to listen to Dolby Digital, DTS or PCM materials
that may be stored on the disc.

In addition, the AVR 347 will convert analog video signals to the HDMI
format, upscaling to high-definition 720p resolution. Source signals
with 1080i or 1080p resolution are passed via the HDMI Output to
your display at their original high-quality resolution, depending on your
display’s capabilities. You may view the AVR 347’s own on-screen
display menus using the HDMI output.

IMPORTANT NOTE:

The AVR 347 cannot convert 1080i or

1080p analog video signals to the HDMI format, and downconverts
them to 720p for the Component Video Outputs. This affects users
of Microsoft

Xbox

360 systems and some older set-top boxes.

If your digital cable television set-top box outputs 1080i or better
video via component video outputs and is not equipped with an
HDMI output, contact your cable operator for a replacement.

For Xbox 360 and satellite television customers, either change
the settings on your source device to ensure that it outputs only
720p video through its component video outputs, which the
AVR can convert to the HDMI format, or connect the AVR’s
Component Video Monitor Outputs to the video display.
Although you could connect the source device’s component
video outputs directly to your video display, you would then
have to select the correct video input on the display, depending
on which source input on the AVR was in use.

The physical HDMI connection is simple. The connector is shaped for
easy plug-in (see Figure 4). If your video display has a DVI input, you
may use an HDMI-to-DVI adapter (not included) to connect it to the
AVR’s HDMI Output.

Figure 4 – HDMI Connection

HDMI cable runs are usually limited to about 10 feet. The AVR 347
incorporates a repeater, which allows an additional 10 feet of cable
between the source device and the video display.

If your video display or source device is not HDMI-capable, use one of the
analog video connections (composite, S- or component video) and if available
on your source device, either a coaxial or optical digital audio connection.

Coaxial digital audio jacks are usually color-coded in orange. Although
they look similar to analog jacks, they should not be confused, and you
should not connect coaxial digital audio outputs to analog inputs or
vice versa. See Figure 5.

Figure 5 – Coaxial Digital Audio

Optical digital audio connectors are often covered by a shutter to protect
them from dust. The shutter opens as the cable is inserted. Input con-
nectors are color-coded using a black shutter, while outputs use a gray
shutter. See Figure 6.

Figure 6 – Optical Digital Audio

Due to the nature of digital signals as binary bits, they aren’t subject
to signal degradation the way analog signals are. Therefore, the quality
of all digital audio connections should be the same, although it is
important to limit the length of the cable. Whichever type of connection
you choose, Harman Kardon recommends that you always select the
highest quality cables available within your budget.

Optical

Optical digital
audio cable

Audio Connections

Left Right

Front

(FL/FR)

Center

(C)

Surround

(SL/SR)

Subwoofer

(SUB)