manualshive.com logo in svg

Harken Unit 0 ESP, Installation Manual

Share
Download
Harken Unit 0 ESP Installation Manual Download Page 23

 

ESP Unit 0, 1 

23

Mount Lead Blocks

Note:

 Harken lead blocks referenced below are an available option. Boat manufacturers may have alternate  

methods of running furling line to cockpit.
Furling line can be led down either side of boat. If boat is in slip, consider mounting opposite dock.
Remove four screws on stanchion blocks. Clamp blocks to stanchions. See instructions below.

Tip: Start all four screws before tightening.

7403

OUTBOARD

STANCHION

BLOCK

7403

OUTBOARD

STANCHION

 BLOCK

7402

RATCHET

STANCHION

 BLOCK

STERN

BOW

7401

FORWARD

STANCHION

BLOCK

7403

OUTBOARD

STANCHION

BLOCK

Spool Empty 

(sail furled)

Spool Full 

(sail unfurled)

7401 Forward Stanchion Block

Position 7401 Forward Stanchion Block so line enters 

drum at right angles to headstay and centers vertically 

in opening. Install so line is inside stanchion.

Correct block position is critical to even line  

spooling and ease of furling.

7403 Outboard Stanchion Blocks

Install 7403 Outboard Stanchion Blocks so line is  

outside stanchions.
Number and placement of leads depends on boat 

length and number/configuration of stanchions.

7402 Ratchet Stanchion Block

Mount 7402 Ratchet Stanchion Block as farthest-aft 

lead to prevent line overrides in drum when unfurling.

Position ratchet block so line turns at least 90°.
Install so line is inside stanchion.

Lead line through block so ratchet makes a clicking 

sound when pulling line to furl sail.

 

Tip: Make sure ratchet switch is in “ON" position.  

If there is no clicking sound, lead line through block 

in opposite direction.

Lead line to furling line cleat in cockpit.

HCP168 Furling Line Cleat

Install so line is angled as shown. Use #10 (5 mm) 

fasteners.

Note

: As furling line lead changes, make sure line 

doesn't chafe against line guard. Rotate drum  

assembly if necessary, see page 22.

Assembly 

Line to Cockpit

90°

Summary of Contents for Unit 0 ESP





































Reviews:

No comments

Brands by name

Popular brands

Load more brands