Track not shown actual size
Part No.
A
B
C
in mm in mm in mm
Low-Profile Track
3154, 3155, 3159, R32.1.5M, R32.2.1M,
R32.3M, R32.3.6M, R32.6M, 3159.8, 3159.12
1
1
/
4
32
3
/
4
19 1
5
/
8
42
High-Beam Track
3156, R32HB.1.5M, R32HB.1.8M,
R32HB.2.5M, R32HB.3.6M
1
1
/
4
32 2
1
/
4
57 1
3
/
16
30
Curved Track Limitations
Cars will not roll on curved track if the radius is under the minimum listed below. A shorter car can roll
on a smaller radius. Refer to the chart below and make sure the radius is equal or greater than the radius
listed for the car. To find the radius go to www.harken.com.
Car
Minimum radius
ft
m
3160/3163/3164/3176/3177
T3201B, T3202B, T3203B, T3205B,
T3221B, T3222B, T3231B, T3232B,
T3241B, T3242B
8
2.44
3161/3165/3166
3172/ 3178/3179
T3201B.HL, T3202B.HL, T3203B.HL,
T3205B.HL, T3221B.HL, T3222B.HL,
T3231B.HL, T3232B.HL, T3241B.HL,
T3242B.HL, T3243B.HL
18
5.49
T3204B.HL, T3224B.HL, T3234B.HL,
T3244B.HL
18
5.49
3167
T3204B, T3224B, T3234B, T3244B
24
7.32
Radius*
Track for Unsupported Spans
Harken high beam track is designed for unsupported
spans. The length of span depends on the load on the
car. The higher the car load the less span the track can
handle. If the car is sized correctly, car length determines
the spanning capability. Longer, high-load (HL) cars
require shorter spans because the loads are so much
greater. See track spanning chart in track instructions.
www.harken.com
Track Compatibility
C B C A R S O N LY R O L L O N C B T R A C K
32mm cars listed above roll on the following tracks.
Note:
32mm cars are CB style and only roll on CB
track listed below
. Older tracks do not have the grooves at the waist for the keeper wires. If cars do not
fit you must replace track. Contact Harken.
Stand-Up Toggle
Soft
Attachment Post
Stand-Up Toggles
– Harken standup toggles fit specifc Harken
blocks. To determine mainsheet block compatibility see
instructions. (Add Link)
Soft Attachment (T3205B, T3205B.HL)
– To attach
loops or straps, remove stop screws and push attach-
ment post out. Assemble post using blue Loctite on screws.
Attaching Mainsheet and Control Blocks
*Applies to vertical
and horizontal bends.
SPAN (Inches/Meters)
SAIL AREA (Feet
2
/Meters
2
)
Monohulls Only
Mid-boom
End-boom
32 mm High-Beam
Track Spanning Chart
700
65
650
60
600
56
550
51
500
46
450
42
400
37
350
33
300
28
45
1.14
60
1.52
75
1.9
90
2.27
Installing Traveler Car on Track
Position car at end of track and gently roll on. Car should roll on easily, if not check to make sure you are
using CB track.
Do not remove ball retaining wires.
Cars will not roll unless they have retaining clips.
If
any balls are lost refer to following instructions for quantities and how to load.
Attaching Splice to Deadend on Car or Controls
To attach premade splice, pass eye through bail and run tail
through to make a hitch without undoing bail. If line is too large
for this, remove one screw and rotate dead-end eyestrap to load
the splice. Reassemble screws using thead locking solution such
as Loctite
®
blue.
High-
Beam
A
B
C
A
B
Groove at waist
for keeper wires.