background image

t

Please read these instructions carefully before installing, servicing, or operating the equipment. 

This manual may be modified without notice. See: www.harken.com/manuals for updated versions.  

PLEASE SAVE THESE INSTRUCTIONS

BATTCAR SWITCH SYSTEM  

INSTALLATION MANUAL

18 mm

Installation Manual – Intended for specialized personnel or expert users

4679 11/1

4

Introduction

 

Safety precautions 

2

Preassembly

Tools 2
Parts 

3 - 4

Sizing/sail modification/switch height 

5

Top track length 

6

Track length 

6

Assembly—Slug-Mount Track

Cut top track to length 

7

Check fit of mounting slugs and car 

7

Install track  

8 - 9

Install switch 

10 - 11

Assembly—Drill and Tap Track

Removing old track 

12

Mount track to carbon mast 

12

General instructions 

12

Install switch 

13

Install track 

14 - 15

Install top stop 

15

Commissioning

Loading headboard assembly 

16

Loading cars 

16

Attaching sail 

16

Lazy Jacks 

17

Operation

Raising sail 

17

Sailmakers Instructions

Dimensions 18
Installing headboard car assembly 

18

Distance between attachment points 

19

Setting reef points 

19

Replacement Parts 

20 - 21

 

Troubleshooting/Warranty 

22

Summary of Contents for HC7906

























Reviews: