Loading Ball Bearings into CB Cars
Ball Replacement Chart
Car
Series
Balls/Car
Balls
Order
Balls/Set
Ball Ø
1624/1626/1628/1640
Midrange
48
Torlon
1526
25
5/16"(8mm)
1625/1627/1629/1641
Midrange Long
60
Torlon
1526
25
5/16"(8mm)
Printed in USA 4999/10-08
Traveler Cars:
Clean by frequently flushing with fresh water. Periodically clean car by
squirting a detergent/water solution into center openings. Roll car back and forth to
distribute evenly then flush bearings with fresh water.
Do not use spray lubricants because ball bearings may skid not roll. Apply one to two
drops of McLube
®
OneDrop
™
to ball contact surfaces of track. Roll car back and
forth through OneDrop
™
several times to distribute onto bearings. Wipe remaining
OneDrop
™
off track. OneDrop
™
is preferred but you can also use one to two drops of a
light machine oil, such as 3-in-1. Too much oil attracts dirt.
Track:
Clean with detergent and water.
Important:
Exposure to some teak cleaners and other caustic solutions can result
in discoloration of part and is not covered under the Harken warranty.
For additional safety, maintenance and warranty information see www.harken.com or
the Harken
®
catalog.
Maintenance
Warranty
Inspect
Frequently inspect shackles and control block fittings for signs of fatigue and replace as
necessary. Make sure every installation includes Harken track end stops. Arrange control
tackle so cars do not hit end stops under load.
Position car on edge with
retaining clip in place. Gently
push one ball at a time into
car from center of clip. Allow
balls to roll into return race
and insert remaining balls.
Do not overfill the car!
Loading Ball Bearings into CB Cars
Ball Replacement Chart
Car
Series
Balls/Car
Balls
Order
Balls/Set
Ball Ø
1624/1626/1628/1640
Midrange
48
Torlon
1526
25
5/16"(8mm)
1625/1627/1629/1641
Midrange Long
60
Torlon
1526
25
5/16"(8mm)
Printed in USA 4999/10-08
Traveler Cars:
Clean by frequently flushing with fresh water. Periodically clean car by
squirting a detergent/water solution into center openings. Roll car back and forth to
distribute evenly then flush bearings with fresh water.
Do not use spray lubricants because ball bearings may skid not roll. Apply one to two
drops of McLube
®
OneDrop
™
to ball contact surfaces of track. Roll car back and
forth through OneDrop
™
several times to distribute onto bearings. Wipe remaining
OneDrop
™
off track. OneDrop
™
is preferred but you can also use one to two drops of a
light machine oil, such as 3-in-1. Too much oil attracts dirt.
Track:
Clean with detergent and water.
Important:
Exposure to some teak cleaners and other caustic solutions can result
in discoloration of part and is not covered under the Harken warranty.
For additional safety, maintenance and warranty information see www.harken.com or
the Harken
®
catalog.
Maintenance
Warranty
Inspect
Frequently inspect shackles and control block fittings for signs of fatigue and replace as
necessary. Make sure every installation includes Harken track end stops. Arrange control
tackle so cars do not hit end stops under load.
Position car on edge with
retaining clip in place. Gently
push one ball at a time into
car from center of clip. Allow
balls to roll into return race
and insert remaining balls.
Do not overfill the car!
Loading Ball Bearings into CB Cars
Ball Replacement Chart
Car
Series
Balls/Car
Balls
Order
Balls/Set
Ball Ø
1624/1626/1628/1640
Midrange
48
Torlon
1526
25
5/16"(8mm)
1625/1627/1629/1641
Midrange Long
60
Torlon
1526
25
5/16"(8mm)
Printed in USA 4999/10-08
Traveler Cars:
Clean by frequently flushing with fresh water. Periodically clean car by
squirting a detergent/water solution into center openings. Roll car back and forth to
distribute evenly then flush bearings with fresh water.
Do not use spray lubricants because ball bearings may skid not roll. Apply one to two
drops of McLube
®
OneDrop
™
to ball contact surfaces of track. Roll car back and
forth through OneDrop
™
several times to distribute onto bearings. Wipe remaining
OneDrop
™
off track. OneDrop
™
is preferred but you can also use one to two drops of a
light machine oil, such as 3-in-1. Too much oil attracts dirt.
Track:
Clean with detergent and water.
Important:
Exposure to some teak cleaners and other caustic solutions can result
in discoloration of part and is not covered under the Harken warranty.
For additional safety, maintenance and warranty information see www.harken.com or
the Harken
®
catalog.
Maintenance
Warranty
Inspect
Frequently inspect shackles and control block fittings for signs of fatigue and replace as
necessary. Make sure every installation includes Harken track end stops. Arrange control
tackle so cars do not hit end stops under load.
Position car on edge with
retaining clip in place. Gently
push one ball at a time into
car from center of clip. Allow
balls to roll into return race
and insert remaining balls.
Do not overfill the car!
Loading Ball Bearings into CB Cars
Ball Replacement Chart
Car
Series
Balls/Car
Balls
Order
Balls/Set
Ball Ø
1624/1626/1628/1640
Midrange
48
Torlon
1526
25
5/16"(8mm)
1625/1627/1629/1641
Midrange Long
60
Torlon
1526
25
5/16"(8mm)
Printed in USA 4999/10-08
Traveler Cars:
Clean by frequently flushing with fresh water. Periodically clean car by
squirting a detergent/water solution into center openings. Roll car back and forth to
distribute evenly then flush bearings with fresh water.
Do not use spray lubricants because ball bearings may skid not roll. Apply one to two
drops of McLube
®
OneDrop
™
to ball contact surfaces of track. Roll car back and
forth through OneDrop
™
several times to distribute onto bearings. Wipe remaining
OneDrop
™
off track. OneDrop
™
is preferred but you can also use one to two drops of a
light machine oil, such as 3-in-1. Too much oil attracts dirt.
Track:
Clean with detergent and water.
Important:
Exposure to some teak cleaners and other caustic solutions can result
in discoloration of part and is not covered under the Harken warranty.
For additional safety, maintenance and warranty information see www.harken.com or
the Harken
®
catalog.
Maintenance
Warranty
Inspect
Frequently inspect shackles and control block fittings for signs of fatigue and replace as
necessary. Make sure every installation includes Harken track end stops. Arrange control
tackle so cars do not hit end stops under load.
Position car on edge with
retaining clip in place. Gently
push one ball at a time into
car from center of clip. Allow
balls to roll into return race
and insert remaining balls.
Do not overfill the car!
