background image

The manufacturer further rejects any claims for damages due to improper use, negligence,
modifications, repair attempts by unauthorized persons or force majeure . 

The repair and/or the replacement of defective parts does not lead to an extension or a 
new start of the warranty period according to the guarantee conditions. 

ATTENTION!

Should problems occur when operating your product please 

immediately contact your local distributor or an authorized 
representative to clarify wether the malfunction is covered by 
guarantee and/or warranty provisions.

Do not, 

under any circumstances

, make alterations or repairs to 

your product on your own!

The company 

eCHARGE Hardy Barth GmbH

 guarantees the proper operation of the 

present product after delivery within the scope of the lawfully valid warranty. 

The warranty is limited to such damage that is attributable to normal use and to obvious 
material or manufacturing defects. 
In these cases, the manufacturer will attempt to restore the proper functioning of the 
product in cooperation with the local distributor. 
Any costs incurred for the transport of the product shall be borne by the customer. 

If the serial number has been removed from the wallbox through the fault of the customer, 
or if it has been altered or is illegible, all rights granted under the warranty conditions shall 
lapse and only the warranty period prescribed by law shall apply. 

If the customer orders repair or replacement work to be carried out outside the business 
hours of 

eCHARGE Hardy Barth GmbH

, the hourly wage and travel costs outside normal 

business hours (Monday – Friday, 9:00 am – 16:00 pm) will be charged to the customer 
according to the current price list. 

Customers service for questions, complaints and objections: 

on weekdays from 9 am – 12 pm / 2 pm – 4 pm 
telephone: +49 9666 / 188 1350
e-mail at 

[email protected]

Please have the serial number, the product name of the wallbox and your 
customer number ready!

Instruction Manual 

cPµ1

 

charging station

Version: 1.3.5

27

Summary of Contents for cPm1




























Reviews: