Harbor Freight Tools LuminarWORK 69286 Owner'S Manual & Safety Instructions Download Page 3

Page 3

For technical questions, please call 1-800-444-3353.

Item 69286

        

SAFET

y

Op

ERA

TION

M

AINTENAN

c

E

SETU

p

Lithium Battery Safety Warnings

  

LITHIUM BATTERIES STORE A 

LARGE AMOUNT OF ENERGy

AND WILL VENT FIRE OR 

EXpLODE IF MISTREATED:

1.

Keep Battery pack dry.

2.

DO NOT DO ANy OF THE FOLLOWING 

yy

TO THE BATTERy p

TO THE BATTER

TO THE BATTER

A

y p

y p cK:

a.

Open,

b.

Drop,

c.

Short-circuit,

d.

puncture,

e.

Incinerate, or

f.

Expose to temperatures greater than 140°F.

3. Charge Battery Pack only according 

to its Adapter’s instructions.

4. Inspect Battery Pack before every use; 

do not use or charge if damaged.

 SAVE THESE INSTRUcTIONS.

Grounding

TO pREVENT ELEcTRIc SHOcK AND DEATH 

FROM INcORREcT GROUNDING WIRE cONNEcTION:

check with a qualified electrician if you are in doubt as to whether the outlet is properly 

grounded.  Do not modify the power cord plug provided with the Adapter.  Do not use the Adapter 

if the power cord or plug is damaged.  If damaged, have it repaired by a service facility before use.  If the 

plug will not fit the outlet, have a proper outlet installed by a qualified electrician.

Outlets for 2-prong plug

1. Tools marked “Double Insulated” do not 

require grounding.  They have a special 

double insulation system which satisfies 

OSHA requirements and complies with 

the applicable standards of Underwriters 

Laboratories, Inc., the Canadian Standard 

Association, and the National Electrical Code.

2. Double insulated tools may be used in either of the 

120 volt outlets shown in the preceding illustration.

  

(See Outlets for 2-prong plug.)

Extension cords

Note:

  Extension cords must not be used with this item’s Adapter.

  Extension cords must not be used with this item’s Adapter.

Symbology

Double Insulated

Canadian Standards Association

Underwriters Laboratories, Inc.

V~

Volts Alternating Current

A

Amperes

WARNING marking concerning Risk 

of Eye Injury.  Wear ANSI-approved 

safety goggles with side shields.

Read the manual before 

set-up and/or use.

WARNING marking 

concerning Risk of Fire.  

WARNING marking concerning 

Risk of Electric Shock.  

Properly connect Adapter’s power 

cord to appropriate outlet.

WARNING marking concerning 

Risk of Explosion.  

Do not puncture, short, or open 

battery packs and do not charge 

damaged battery packs.

Summary of Contents for LuminarWORK 69286









Reviews: