background image

6.

DRESS SAFELY.  

Do not wear loose clothing or jewelry, as they can become

caught in moving parts.  Wear a protective hair covering to prevent long hair from
becoming caught in moving parts.  If wearing a long-sleeve shirt, roll sleeves up
above elbows.

7.

DO NOT OVERREACH.

  Keep proper footing and balance at all times to prevent

tripping, falling, back injury, etcetera.

8.

INDUSTRIAL APPLICATIONS MUST FOLLOW OSHA REQUIREMENT.

9.

STAY ALERT.

  Watch what you are doing at all times.  Use common sense.  Do

not use this product when you are tired or distracted from the job at hand.

10.

CHECK FOR DAMAGED PARTS.

  Before using this product, carefully check that

it will operate properly and perform its intended function.  Check for damaged
parts and any other conditions that may affect the operation of this product.
Replace or repair damaged or worn parts immediately.

11.

REPLACEMENT PARTS AND ACCESSORIES:

 When servicing, use only identi-

cal replacement parts.  Only use accessories intended for use with this product.
Approved accessories are available from Harbor Freight Tools.

12.

MAINTAIN THIS PRODUCT WITH CARE.

  Keep this product clean and dry for

better and safer performance.

13.

MAINTENANCE:

  For your safety, service and maintenance should be performed

regularly by a qualified technician.

14.

USE THE RIGHT TOOL FOR THE JOB.

  Do not attempt to force a small tool or

attachment to do the work of a larger industrial tool.  There are certain applica-
tions for which this tool was designed.  It will do the job better and more safely at
the rate for which it was intended.  Do not modify this tool, and do not use this
tool for a purpose for which it was not intended.

15.

WARNING:

  The warnings, precautions, and instructions discussed in this

manual cannot cover all possible conditions and situations that may occur.  The
operator must understand that common sense and caution are factors, which
cannot be built into this product, but must be supplied by the operator.

SPECIFIC PRODUCT WARNINGS AND PRECAUTIONS

1.

KEEP FINGERS AND HANDS SAFELY AWAY FROM THE ROLLERS (part
#23), GEAR WHEEL (part #17), AND GEARS (parts #12, #13) AT ALL TIMES
TO AVOID PERSONAL INJURY.  (See Figure A, next page.)

SKU 2458

PAGE 3

Brought To You By Augusta Flint

Summary of Contents for CEN-TECH 2458









Reviews: