Harbor Freight Tools 95666 Assembly And Operating Instructions Manual Download Page 2

PRODUCT SPECIFICATIONS

SAVE THIS  MANUAL

You will need this manual for the safety warnings and precautions, assembly, operating,
inspection, maintenance and cleaning procedures, parts list and assembly diagram.
Keep your invoice with this manual.  Write the invoice number on the inside of the front
cover.  Keep this manual and invoice in a safe and dry place for future reference.

GENERAL SAFETY RULES AND PRECAUTIONS

WARNING!

READ AND UNDERSTAND ALL INSTRUCTIONS

Failure to follow all instructions listed below may result in

electric shock, fire, and/or serious injury.

SAVE THESE  INSTRUCTIONS

WORK AREA

1.

Keep your work area clean and well lit.  Cluttered benches and dark areas
invite accidents.

2.

Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases, or dust.  
Power tools create

SKU 95666          For technical questions, please call 1-800-444-3353         PAGE 2

The Emission Control System for this product’s engine is warranted for standards set by the U.S.

Environmental Protection Agency.  For warranty information, refer to the last pages of this manual.

This product requires a 25:1 ratio of fuel and 2-cycle oil to be added to its fuel tank before starting.

Attempting to start the Engine with an improper fuel mix, low or no fuel mix WILL ruin the Engine

and void the warranty.

The Engine’s Carburetor may need to be adjusted by a qualified mechanic for efficient high-

altitude use.

Item Description 

Drive Size 

1” 

Maximum Bolt Capacity 

1-5/8” 

Output Torque Range 

406 < - > 1250 Ft./Lb. 

Gear Box Settings 

Reverse/Neutral/Forward 

Engine Specifications 

Engine Type: Two-Stroke / Forced Air Cooling / Single Cylinder / Recoil Start 
Engine Displacement: 51.7 cc 
Engine Idling RPM: 2700 
Engine No Load RPM: 9880 
Engine Torque RPM: 7120 
Fuel Tank Capacity: 34 Ounces (0.26 Gal.) 
Fuel Mixture Required: 25:1 (25 Parts Unleaded Gasoline/1 Part 2-Cycle Oil) 
Spark Plug Type: Torch 

®

  L7T 

EPA Approved 

Accessories 

Side D-Handle (Qty. 1) / Top D-Handle (Qty. 1) / Spark Plug Wrench (Qty. 1) 
4mm Hex Wrench (Qty. 1) / 5mm Hex Wrench (Qty. 1) / 6mm Hex Wrench (Qty. 1) 
10 < - > 13mm Spanner (Qty. 1) 

Net Weight 

39.6 Pounds 

 
 

Summary of Contents for 95666























Reviews: