background image

SKU 95621 

 

 

    Page 6  

Parts List and Diagram

        NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts.

Part

Description

Q’ty

1

Support Legs

2

2

Base Bars

2

3

Adjusting Handle

1

4

Roller Head

1

5

Extendable Arm

1

6

Large Screw

1

Part

Description

Q’ty

7

Small Screw

3

8

Large Washer

2

9

Small Washer

2

10

Large Nut

1

11

Small Nut

1

12

Cylinder Nut

4

ThE MANUFACTURER AND/OR DISTRIBUTOR hAS PROVIDED ThE PARTS LIST AND ASSEMBLY DIAGRAM IN ThIS 

MANUAL AS A REFERENCE TOOL ONLY.  NEIThER ThE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESEN-
TATION OR WARRANTY OF ANY KIND TO ThE BUYER ThAT hE OR ShE IS QUALIFIED TO MAKE ANY REPAIRS TO ThE 
PRODUCT, OR ThAT hE OR ShE IS QUALIFIED TO REPLACE ANY PARTS OF ThE PRODUCT.  IN FACT, ThE MANUFAC-
TURER AND/OR DISTRIBUTOR ExPRESSLY STATES ThAT ALL REPAIRS AND PARTS REPLACEMENTS ShOULD BE 
UNDERTAKEN BY CERTIFIED AND LICENSED TEChNICIANS, AND NOT BY ThE BUYER.  ThE BUYER ASSUMES ALL 
RISK AND LIABILITY ARISING OUT OF hIS OR hER REPAIRS TO ThE ORIGINAL PRODUCT OR REPLACEMENT PARTS 

ThERETO, OR ARISING OUT OF hIS OR hER INSTALLATION OF REPLACEMENT PARTS ThERETO.

1

1

2

3

4

5

6

7

8

9

10

11

12

Summary of Contents for 95621







Reviews: