background image

Page 6

for technical questions, please call 1-800-444-3353.

SKU 67378 

        

operating inStructionS

  read the entire important 

SafetY information 

section at the beginning of this 

manual including all text under 

subheadings therein before set 

up or use of this product.

tool Set up

 

to preVent 

SeriouS injurY 

from acciDental 

operation: 

turn the power Switch of the 

tool off and remove the 

batteries before adjusting tool 

or installing accessories.

figure 2

Lock Nut (20)

Tapered Bushing (19)

Threaded Insert (24)

Upper Leg (15)

note:

 When adjusting the length of the 

Metal Detector, be careful to keep 

the plastic Tapered Bushing (19) in 

place with the smaller end toward the 

smaller end of the Lock Nut (20). 
To attach the two legs, slide the 

1. 

Threaded Insert (24) over the end 

of the Upper Leg (15), making sure 

that the tabs inside the Insert lock 

into the cut-outs at the end of the 

leg. Insert the tapered end of the 

Tapered Bushing (19) into the Lock 

Nut (20) and lightly thread the Nut 

over the Insert (24). Slide the Lower 

Leg (18) into the Lock Nut. To take 

the slack off the cord, rotate the 

Lower Leg, enabling the cord to wind 

around the two Legs. Rotate the Nut 

counterclockwise to lock the Legs.
To adjust the length of the Legs, turn 

2. 

the Lock Nut in a clockwise direction, 

slide the Lower Leg to the desired 

extension length and turn the Nut 

counterclockwise to secure the Legs 

together.
To adjust the angle of the Search 

3. 

Coil, loosen the Coil Pivot (21) and 

Knob Bolt (22) and tilt it. Position the 

Search Coil so that it is parallel to 

the ground when holding the unit by 

the Handle with your arm in the Arm 

Support (13). 
If needed, re-adjust the length of the 

4. 

Metal Detector after adjusting the 

position of the Search Coil.   

Batteries

Make sure the On/Off/Volume control 

1. 

is set to OFF. Slide the Battery Cover 

(26) off of the back of the Control 

Box and insert six AA batteries (sold 

separately), aligning polarities as 

indicated. Replace the Battery Cover.

note:

 Use only fresh batteries of the 

required size and type. Do not mix 

old and new batteries, different types  

(standard, alkaline, or rechargeable), 

or rechargeable batteries of different 

capacities. 
Always remove old or weak batteries. 

Batteries can leak chemicals that can 

destroy electric parts.
If you do not plan to use the detector 

for a week or more, remove the 

batteries.

Summary of Contents for 67378














Reviews: