background image

SKU 66163 

For technical questions, please call 1-800-444-3353. 

Page 5

SpECiFiCATiOnS

Power Source

12 VDC

Plug Type

12 VDC Cigaretter Lighter Plug

Fuse Equipped

No.  Must be connected to a fused 12 volt 

circuit.

Features

Wet & Dry Hand-Held Vacuum.

High Power Motor for Efficient Cleaning.

Detachable Container with Filter for 

Convenient Cleaning.

Accessories

Liquid Pick-Up Nozzle (Qty. 1)

Small Crevise Nozzle (Qty. 1)

Large Crevise Nozzle (Qty. 1)

UnpACKing

When unpacking, check to make sure 

that the item is intact and undamaged.  If 

any parts are missing or broken, please 

call Harbor Freight Tools at the number 

shown on the cover of this manual as soon 

as possible.

OpERATing inSTRUCTiOnS

  Read the EnTiRE iMpORTAnT 

SAFETY inFORMATiOn 

section at the beginning of this 

manual including all text under 

subheadings therein before set 

up or use of this product.

 

TO pREVEnT 

SERiOUS injURY 

FROM ACCiDEnTAL 

OpERATiOn: 

Turn the power Switch (5) of 

the Auto Vacuum to its “OFF” 

position and unplug the tool 

from the vehicle’s cigarette 

lighter outlet before 

assembling or making any 

adjustments to the tool.

note:

  For additional information regarding 

the parts listed in the following pages, 

refer to the Assembly Diagram near 

the end of this manual.

To pick up 

1. 

solids

, attach either the 

Long Nozzle (6) or the short Nozzle 

(10) to the Collector (2) as follows: a) 

To attach the sort Nozzle (1), push 

the short end of the Nozzle into the 

opening at the front end of the Col-

lector, making sure that the deflec

-

tor angle is in the same orientation 

as the tip of the Collector.  Push the 

Nozzle in until snug.  b) To attach the 

long Nozzle (6), slide it over the end 

of the short nozzle, again keeping 

in mind the orientation of the Nozzle 

opening with the angle of the Collec-

tor opening.
To pick up 

2. 

liquids

, insert the Liquid 

Pick-Up Nozzle (7) into the opening 

at the end of the Collector (2).  

iM-

pORTAnT:  

Make sure that the liquid 

vacuumed 

does not

 rise above the 

“MAX” mark on the Collector. 

(See Figure A.)

To power the Auto Vacuum, insert the 

3. 

tool’s 12 Volt Power Plug (11) into a 

vehicle’s 12 volt cigarette lighter/ac

-

cessories outlet. 

iMpORTAnT:  

In certain vehicles, 

you may have to switch the ignition to 

the 

accessory

 mode before the Vacu-

um will operate.  

(See Figure A.)

Press and hold the Power Switch 

4. 

(5) to run the Auto Vacuum.  While 

running, the Power-On Light (4) will 

illuminate.  

(See Figure A.)

Summary of Contents for 66163









Reviews: