background image

Page 3

For technical questions, please call 1-888-866-5797.

Item 62307 

        

SAFET

y

Op

ERA

TION

M

AINTENAN

c

E

SETU

p

6. 

Only use and store in normal temperature 

environments. 

Extremes in temperature can 

shorten effectiveness of electronic devices 

and melt or damage plastic parts.

7. 

Avoid electrical shock. 

Any metal detector may 

discover underground power lines, explosives 

or other items which when struck could cause 

personal injury.  Do not use this product in areas 

where there might be underground electric lines 

or pipes buried at shallow depths.  Never search 

in military zones where bombs or other explosives 

may be buried.  Avoid striking any line known or 

suspected to be carrying electric power.  Do not 

search any pipeline, particularly if it could contain 

a flammable gas or liquid.  In areas of uncertain 

conditions, use reasonable caution before using 

the Tool.  If there is any question about a condition 

being safe of unsafe, do not operate the Tool.

8. 

Keep the Metal Detector away from any lights, 

TVs, computers, and mobile telephones. 

 These 

can all cause electromagnetic interference.

9. 

Only the Search coil and black section of the 

Lower Leg are waterproof. 

Do not immerse the 

unit beyond the black section of the Lower Leg.

10. 

Keep the Tool clean.  

Wipe the housing after 

each use.  The search coil is washable and can 

be fully submerged.  Never submerge the control 

housing.  Protect the control housing from rain, 

blowing surf and heavy mist.  Disassemble the 

Leg and wipe it clean after use in sandy areas.

11. 

Use the right tool for the job

.  There are certain 

applications for which this tool was designed. 

Do not modify this tool and do not use this tool 

for a purpose for which it was not intended.

12. 

This product is not a toy. 

 Keep 

it out of reach of children.

13. 

people with pacemakers should consult their 

physician(s) before use. 

 Electromagnetic fields 

in close proximity to heart pacemaker could cause 

pacemaker interference or pacemaker failure.  In 

addition, people with pacemakers should: 

•  Avoid operating alone. 

•  Properly maintain and inspect 

to avoid electrical shock.

14. WARNING: This product contains or, when 

used, produces a chemical known to the State 

of California to cause cancer and birth defects 

or other reproductive harm.  (California Health 

& Safety Code § 25249.5, 

et seq.

15. The warnings, precautions, and instructions 

discussed in this instruction manual cannot 

cover all possible conditions and situations 

that may occur.  It must be understood by the 

operator that common sense and caution are 

factors which cannot be built into this product, 

but must be supplied by the operator.

  SAVE THESE 

INSTRUcTIONS.

Specifications

Electrical Input 6 AA Batteries (not included)
Earphone Jack 3.5 mm mini-jack Socket

Functions

Sensitivity Adjuster; Metal-

Type Discriminator; All-Metal 

Indicator; Tone Adjuster; 

Volume Control; Target Locator; 

Low Battery Indicator; Auto 

Ground Balance; Mode Selector

Summary of Contents for 62307













Reviews: