background image

Visit our website at: http://www.harborfreight.com

Email our technical support at: [email protected]

Email our engine support at: [email protected]

Owner’s Manual & Safety Instructions

Save This Manual

 

Keep this manual for the safety warnings and precautions, assembly, 

operating, inspection, maintenance and cleaning procedures.  Write the product’s serial number in the 

back of the manual near the assembly diagram (or month and year of purchase if product has no number). 

Keep this manual and the receipt in a safe and dry place for future reference. 

20k

Using a generator indoors CAN 

KILL YOU IN MINUTES.
Generator exhaust contains carbon monoxide.  

This is a poison you cannot see or smell.

NEVER use inside 

a home or garage, 

EVEN IF doors and 

windows are open.

Only use OUTSIDE 

and far away from 

windows, doors, 

and vents.

When unpacking, make sure that the product is intact 

and undamaged.  If any parts are missing or broken, 

please call 1-888-866-5797 as soon as possible.

Copyright

©

 2020 by Harbor Freight Tools

®

.  All rights reserved.  

No portion of this manual or any artwork contained herein may be reproduced in 

any shape or form without the express written consent of Harbor Freight Tools.  

Diagrams within this manual may not be drawn proportionally.  Due to continuing 

improvements, actual product may differ slightly from the product described herein.  

Tools required for assembly and service may not be included.

Read this material before using this product. 

Failure to do so can result in serious injury. 

SAVE THIS MANUAL.

Summary of Contents for 57080





























Reviews: