![background image](http://html.mh-extra.com/html/harbor-breeze/40030/40030_quick-start-manual_596210002.webp)
ASSEMBLY INSTRUCTIONS
1
3
5
7b
9
8
1.
Turn off circuit breakers and wall switch to
the fan supply line leads.
DANGER:
Failure to disconnect the
power supply prior to installation may
result in serious injury or death.
2. With the mounting bracket (B) resting
inside the canopy (C), partially install two
mounting bracket screws (EE) into the
two holes surrounded by the J-slots in the
canopy (C). Then, remove the mounting
bracket (B) from the canopy (C).
3. Using the screws and washers provided
with the outlet box (not included), secure
the mounting bracket (B) to a “Ceiling
Fan Rated” outlet box. The opening of
mounting bracket (B) should open toward
the floor.
4. Slide the accessory downrod (sold
separately) into the yoke of the ceiling fan.
Install the accessory downrod according
to the instruction manual included with the
ceiling fan.
5. If using this item on an angled ceiling,
snap out the perforated section of the
canopy cover (D).
6. Slide the canopy (C) of your choice and
the ball (A) onto the accessory downrod.
Note:
Ball (A) must be positioned with the
holes near the top of the downrod.
2
B
B
C
B
EE
A
A
A
DD
D
A
C
CC
BB
BB
DD
CC
AA
E
10
6
7a
Printed in China
7a. If using a 3/4-inch diameter
accessory downrod,
attach the ground
wire (CC) to the smaller hole in the
accessory downrod using the ground
screw (BB). Then slide the pin (DD)
into the two large holes at the top of the
downrod.
7b.
If using a 1/2-in. diameter downrod,
slide the ball adapter (E) onto the
accessory downrod and down into the
center of the ball (A). Then, attach the
ground wire (CC) to the small hole in
the top of the accessory downrod with
the ground screw (BB). Align the large
holes in the ball adapter (E) with the
large holes in the top of the accessory
downrod, then slide pin (DD) through
larger holes in the ball adapter (E) and
downrod.
8. Raise the ball (A) to the top of accessory
downrod, aligning hole in the ball (A)
with set screw hole at top of downrod.
This will allow the pin (DD) to fall into
the proper slot in the top of the ball (A).
Then, secure the ball (A) to the top of
the accessory downrod using the set
screw (AA).
9. Lift the ball (A) along with the fan into
the opening in the mounting bracket (B).
Align one of the slots in the ball (A) with
tab in the mounting bracket (B).
DANGER:
Failure to align a slot in
the ball (A) with the tab in the mounting
bracket (B) may cause fan to wobble or
fall, which could result in serious injury
or death.
10. Align the canopy (C) over the
loose mounting bracket screws (EE)
preassembled on the mounting bracket
(B) in Step 2. Then, twist canopy (C) to
lock. Insert two more mounting bracket
screws (EE) into the round holes of the
canopy (C). Tighten all four mounting
bracket screws (EE).
Opening
Accessory
Downrod
Yoke
Tab
Slot
Note:
This item was designed for use with an existing ceiling fan. It will be necessary to purchase a longer downrod in order to install the fan to a vaulted ceiling.
The parts included with this item will be used instead of similar parts included with your fan.
4
Hole
9168 • 101716
B
EE
C
2
Top view
J-slot
DD
Hole