V2408, V2410, VS12
OWNER’S MANUAL
5
V2400
110-120V~ 50/60Hz
220-240V~ FUSE:T2 AL/250V
110-120V~ FUSE:T4 AL/250V
220-240V~ FUSE:T2 AL/250V
110-120V~ FUSE:T4 AL/250V
220-240V~ 50/60Hz
100W
110-120V~ 50/60Hz
220-240V~ 50/60Hz
100W
V2400
V2400
110-120V~ 50/60Hz
220-240V~ FUSE:T2 AL/250V
110-120V~ FUSE:T4 AL/250V
220-240V~ FUSE:T2 AL/250V
110-120V~ FUSE:T4 AL/250V
220-240V~ 50/60Hz
100W
110-120V~ 50/60Hz
220-240V~ 50/60Hz
100W
V2400
V2408/V2410 BACK PANEL
1
INPUT 1 AND 2 KNOBS
These knobs set the volume for the inputs below them.
2
CLIP LEDS
If a Clip LED lights, turn down that input knob, to avoid distorted sound.
3
MIC/GUITAR/LINE SWITCHES
Set these to match the type of source connected to the input below them:
- Mic: for microphones, or line level sources with low output volumes.
- Guitar: for acoustic guitar or guitar pedal board.
- Line: for line level sources.
4
INPUT 1 AND 2 INPUT JACKS
Connect XLR or 1/4-inch cables.
5
INPUT 3 KNOB
Sets the volume for all the inputs below, including Bluetooth
®
audio,
Stereo (AUX) Input and line inputs.
6
BLUETOOTH
®
AUDIO INPUT
Press the On/Pair button to enable Bluetooth
®
and initiate pairing mode:
- To pair, look for VARI V2408 or VARI V2410 from your Bluetooth
®
audio source device.
- LED is lit solid when currently paired, blinking when available for
pairing, and off if Bluetooth
®
has been disabled by a press of the
Bluetooth
®
Off button.
- On/Pair button forces any currently connected Bluetooth
®
audio source
to disconnect, and makes the speaker available for pairing.
- Off button disables Bluetooth
®
.
- Bluetooth On/Off state when turning power off will be remembered and
restored when turning power on.
7
STEREO (AUX) INPUT
This input accepts a stereo or mono unbalanced audio input.
8
BALANCED LINE INPUTS
Balanced or unbalanced line level sources can be connected here.
9
BASS AND TREBLE KNOBS
Adjust the sound of your speaker.
10
VOICING
Pressing the button selects from the VOICINGs:
- Normal: for general use including music playback
- Floor Monitor: for floor monitor use, also may be helpful to avoid
excessive bass from wall mounted speakers
- Sub Cut: for feeding a subwoofer, see (12) for details
11
ROUTING
- Normal (Mono): This speaker will output mono audio.
- Stereo Master: This speaker will operate as the master (left) speaker
of a Smart Stereo pair. Use a mic cable to connect this speaker’s LINK
OUT to the INPUT 1 jack of a second speaker of the same type. All
inputs should be connected to the first master speaker, which will also
set the volume and tone of both speakers.
- Link In: Use this setting for the second speaker of a Smart Stereo pair.
The audio from INPUT 1 will be routed directly to the power amp and
speaker, with all other inputs and controls being ignored. This can
also be used to accept mono audio from a previous speaker, with that
previous speaker determining volume and tone.
12
MIX OUT JACK
- Outputs mono audio.
- When SUB CUT is selected, V2408/V2410 will then crossover the
audio, to keep high frequencies for itself, and send low frequencies
to the subwoofer.
13
LINK OUT JACK
- When ROUTING is set to Smart Stereo, this jack outputs right only
audio to feed a second (right) speaker.
- When ROUTING is set to Normal (Mono), this jack outputs mono audio
to feed a second speaker.
14
CHARGE JACK
Provides power for mobile devices.
15
Switches the power on and off.
16
If the speaker will not power on and you suspect its fuse may have blown,
turn off the power switch, and open the fuse compartment using
a small flat blade screwdriver. If metal strip in fuse is broken, replace
with T4
AL 250V fuse (for 100-120 volt use), or T2 AL/250V fuse
(for 220-240 volt use).
17
Connect power cable here.
18
Configures speaker for your territory’s voltage. 100-120V is the standard
in the USA.
1
2
3
4
5
9
10
11
16
17
18
12
14
15
13
6
7
8
V2400
110-120V~ 50/60Hz
220-240V~ FUSE:T2 AL/250V
110-120V~ FUSE:T4 AL/250V
220-240V~ FUSE:T2 AL/250V
110-120V~ FUSE:T4 AL/250V
220-240V~ 50/60Hz
100W
110-120V~ 50/60Hz
220-240V~ 50/60Hz
100W
V2400
