background image

HA120

www.harbingerproaudio.com

4

Master Section

1.  MASTeR eQ

lOW: 

This shelving control gives 15dB of boost or cut  

at 80Hz and below.

MId: 

This is a band peak equalizer with a control range 

of +/-15dB at 1KHz.

HIGH: 

This shelving control gives 15dB of boost or cut  

at 12KHz and above.

2.  

fX

 

This controls the signal from the input channels, processed 
by the built-in digital delay.

fX MASTeR:

This knob adjusts the mix level of the  

effect sound.

TIMe: 

Turn this knob to the right to increase the interval 

time between delays, to the left to decrease.

3. 

POWeR IndICATOR

 

When the power switch at the rear panel is turned on,  
this indicator will illuminate.

4. 

AUX In COnTROl

 

This knob adjusts the level from the AUX Inputs to the  
Master Volume.

5  MASTeR VOlUMe
 

This knob adjusts the total output Volume. Turn Master 
Volume down before turning unit on or off.

AUX In & ReC OUT

 

The AUX IN Phono Jacks allow MP3/CD players to be  
connected to the amplifier. The RECORD OUTPUT RCA 
Phono Jacks provide signal output to audio equipment.  
The nominal output level and impedance are 
-10dBV/600ohms.

fOOTSWITCH

 

This jack accepts a footswitch (not included) to turn the 
digital delay on or off. Compatible with momentary 
footswitch (normal open circuit).

FOOT

SWITCH

AUX

IN

REC

OUT

HA120

120 WATT

4 CHANNEL MIXER

MID

FX MASTER

TIME

DIGITAL DELAY

PEAK

PEAK

PEAK

PEAK

1

2

5 W

A

T

T

S

AC 1 20V

~

50/60HZ 200W

INSE RT

MAIN  

FUSE:2A 

B

 

SPE AKE R 

OU T 

HA120

USE ONLY WITH 250V FUSE

1

3

2

4

5

6

7

1

2

3

6

4

5

7

Summary of Contents for HA120













Reviews: