1. The Default Arm/Disarm switch for Moblite7
is AUX1(Channel 5),and you can also
HDZERO
customize it with Betaflight Configurator.
3.The default channel map for Moblite7 HDZERO version is TAER1234. Please make sure your
transmitter is matched, otherwise it wouldn't be armed. Toggle the AUX1 Switch ,the Green LED
on the flight controller will getting to be solid, this indicates the motor was armed . And also you
can found
“
Armed" notice displayed on your FPV Goggles or the FPV Monitor. Please make sure
keep the Moblite7 HDZERO level before arming .Be careful and Happy flying !
The following settings are reserved from out of factory. Sometimes maybe you need it after you
updated firmware.Please set Receiver mode to be SPI RX Support from the Configuration tab of
the Betaflight Configurator, then select EXPRESSLRS from the SPI Bus Receiver Provider list.
Don't enable Serial RX since the
Flight controller is integrated
.
Superbee F4 ELRS
SPI Receiver
2.Turn on the Radio transmitter with ELRS TX module installed(Use TX16S as an example) and
move to the MIXES interface, Set CH5 channel to "SF" or other aux channel to ARM/DISARM the
motor
Qty
1
1
4
1
1
1
1
1
1
Item Name
2). Turn on your radio transmitter and running ELRS.LUA v2 version, scroll down the menu and
hit [Bind]. The red LED on the flight controller would
It means bind successfully.
get to be solid.
Re-connect the USB and then you will find link was established.
*Need to update ExpressLRS TX module firmware to
before
v2.0 or v2.x version firmware
binding.Bind procedure video
https://bit.ly/3NeL1hf
1). Connect Moblite7 HDZERO with computer by Plug USB. Running Betaflight configurator and
then move on Receiver tab then hit
“
Bind Receiver
”
.
.The Red LED
Or use CLI bind code "bind_rx"
on the flight controller start blinking fast, it means onboard SPI ELRS receiver is in bind mode.
Notice: The HDZERO whoop lite vtx and nano lite camera can only working while battery was
connected. USB couldn't supply for the whoop lite vtx module and nano lite camera.
TX1 pad was used for Smartaudio
TX2 and RX2 were used for MSP
TX2
RX2
GND
+5V
Video out
VIN
GND
LED_Strip
BUZ-
GND
+5V(BUZ+)
GND
RX1
+5V
M1_C
M1_B
M1_A
M2_A
M2_B
M2_C
M4_A
M4_B
M4_C
M3_A
M3_B
M3_C
TX1
LIPO IN
_ +
Brand Name: Happymodel
Model: Moblite7 HDZERO
Frame wheelbase: 75mm
Weight: 29.5 gram without battery
Size: 98mm*98mm*50mm
Receiver option:
SPI ELRS 2.4GHz
SPI FRSKY 2.4GHz
Compatible with 1S Lipo battery or Lihv battery
Battery Plug: PH2.0
Mobula7 v4 75mm frame +Canopy
SPI Receiver Option1: SuperbeeF4 Lite FC built-in ExpressLRS SPI RX
SPI Receiver Option2: SuperbeeF4 Lite FC built-in Frsky SPI RX
EX1002 KV20000 Unibell brushless motor
Gemfan 1610-2 bi-blades propeller(4cw+4ccw)
HDZero Nano Lite Camera
HDZero Whoop Lite VTX
Spare Canopy
Propeller disassemble tool
Screw driver
