9
:
#
"
9
:
#
"
9
:
#
"
9
:
#
"
신형 아나로그 타이머_220822_01
F
DUAL (time-limit 1c + time-limit 1c)
Power
② - ⑦
When power is applied, OUT1
output and OUT2 output repeat
the “OUT1 ON -> OUT1 OFF ->
OUT2 ON -> OUT2 OFF” operation
according to the T1, T2, and Toff
times until the power is turned off.
T1 and T2 times are the same,
set to ON volume.
Toff time is set to OFF volume.
OUT1
(time-limit)
① - ③
OUT2
(time-limit)
⑥ - ⑧
ON indicator
OUT2
operation display
OFF indicator
OUT1
operation display
Please read the safety information carefully then use the product correctly.
The alerts declared in the manual are classified into
Danger
,
Warning
and
Caution
according to their importance
▍Safety information
28, Gilpa-ro 71beon-gil,
Michuhol-gu, Incheon, Korea
TEL : +82-32-876-4697
http://www.hanyoungnux.com
HANYOUNGNUXCO.,LTD
Analog twin timer
TF62A
Thank you for purchasing Hanyoung Nux products.
Please read the instruction manual
carefully before using this product, and use the product correctly.
Also, please keep this instruction manual where you can see it any time.
MD1105KE220118
INSTRUCTION MANUAL
DANGER
Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury
WARNING
Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury
CAUTION
Indicates a potentially hazardous situation which, if not avoided, may result in minor injury or property damage
CAUTION
• Please do not set “Time” to “0”. This can be a cause of malfunction.
Also, there could be a time difference in timer operation.
Please use it after confirming the time difference.
• Please set or change “Time Range” in the dip switch while the
timer is OFF. If the “Time Range” has been changed to other value
during the operation, please turn off the timer and turn it back on.
• Since this is not explosion-proof structure, please use in a place
where corrosive gas (such as harmful gas, ammonia, etc.),
combustible or explosive gas does not occur.
• Please use in a place where there is no direct vibration and a large
physical impact to the product.
• Please use in a place where there is no water, oil, chemicals, steam,
dust, salt, iron or others
• Please avoid using in a place where excessive amounts of inductive
interference or electrostatic and magnetic noise occur.
• Please avoid using in a place where heat accumulation occurs due
to direct sunlight or radiant heat.
• Please use in a place where the elevation is below 2,000 m.
• Please make sure to inspect the product if exposed to water since
there is a possibility of electric leakage or a risk of fire.
• If there is a lot of noise from the power line, installing an insulated
transformer or a noise filter is recommended.
• When the power is being supplied there should be a preparation
time for the contact output. Please use a delay relay together when
it is used as a signal on the outside of interlock circuit or others.
DENGER
•
The input/output terminals are subject to electric
shock risk. Never let the input/output terminals come
in contact with your body or conductive substances.
• Please install an appropriate protective circuit on the
outside if malfunction, an incorrect operation or failure of the
product may be a cause of leading to a serious accident
and plan for preventing accidents.
• After mounting the product onto a panel, please use a socket
dedicated to the product when connecting with other units
and do not turn on the power until completing wiring to
prevent electric shock.
• Please turn off the power when mounting/dismounting of
the product. This is a cause of electric shock,
malfunction, or failure.
• If the product is used with methods other than specified by the
manufacturer, then it may lead to injury or property damage.
• In order to use this product properly and safely,
we recommend periodic maintenance.
• The warranty of this product (including accessories) is
1 year only when it is used for the purpose it was
intended under normal condition.
WARNING
▍Suffix code
▍Specification
Model
Code
Description
Product configuration
TF62A
□- □ □- □ Analog twin timer 38.4(W) X 42.4(H) X 59.0(D) mm
• TF62A-1N-A
• TF62A-3N-A
• TF62A-6N-A
Time range
1
Maximum time : 1sec / 1min / 1hour / 10sec / 10min / 10hour
3
Maximum time : 3sec / 3min / 3hour / 30sec / 30min / 30hour
6
Maximum time : 6sec / 6min / 6hour / 60sec / 60min / 60hour
Control output
N
No option
power voltage
A 24
–
240 V a.c. 50/60 Hz or 24
–
240 V d.c. dual usage
▍Operation mode
■ Bracket
▍Dimension & Panel cutout
[Unit:mm]
▍Function and name of each part
C
TWIN (time-limit 1c + time-limit 1c)
Power
② - ⑦
When the power is applied, the
OUT2 output turns ON and the
T2 time is displayed.When the
time time reaches T2 , OUT2
output turns OFF, OUT1 output
is ON and time T1 is displayed.
When the time reaches T1 time,
OUT1 output turns OFF and timer
operation stops. Time T1 is set to
volume OFF and time T2 is set to
volume ON.
OUT1
(time-limit)
① - ③
OUT2
(time-limit)
⑥ - ⑧
ON indicator
OUT2
operation display
OFF indicator
OUT1
operation display
Rt : Return Time T1 : out1 on operation time T2 : out2 on operation time
A
FLICKER ON START (time-limit 2c)
Power
② - ⑦
When power is applied, OUT1
output and OUT2 output turn ON
at the same time,
and timekeeping starts.
Until the power is turned off,
OUT1 output and OUT2 output
repeat ON/OFF operation
according to Ton time and
Toff time .
OUT1
(time-limit)
① - ③
OUT2
(time-limit)
⑥ - ⑧
ON indicator
OUT1 & OUT2
operation display
OFF indicator
Rt : Return Time Ton : on operation time Toff : off operation time
B
FLICKER OFF START (time-limit 1c + instantaneous 1c)
Power
② - ⑦
OUT1 output is an instantaneous
output that turns on at the same time
as power is applied, and maintains
the ON state until the power is turned
off regardless of Ton time and Toff
time.When power is applied, OUT2
output remains OFF and timekeeping
starts.Until the power is turned OFF,
the OUT2 output repeats ON/OFF
operation according to the
Ton time and Toff time .
OUT1
(instantaneous)
① - ③
OUT2
(time-limit)
⑥ - ⑧
ON indicator
OUT2
operation display
OFF indicator
Rt : Return Time Ton : on operation time Toff : off operation time
D
FLICKER OFF START (time-limit 2c)
Power
② - ⑦
When power is applied, OUT1
output and OUT2 output remain
OFF, and timekeeping starts.
Until the power is turned OFF
OUT1 output and OUT2 output
repeat ON/OFF operation
according to Ton time and Toff
time .
OUT1
(time-limit)
① - ③
OUT2
(time-limit)
⑥ - ⑧
ON indicator
OUT1 & OUT2
operation display
OFF indicator
Rt : Return Time Ton : on operation time Toff : off operation time
E
FLICKER ON START (time-limit 1c + instantaneous 1c)
Power
② - ⑦
OUT1 output is an instantaneous
output that turns ON at the same
time as power is applied,
and remains ON until power is OFF
regardless of Ton time and Toff
time.When power is applied, OUT2
output turns ON and timekeeping
starts.Until the power is turned
OFF, OUT2 output repeats
ON/OFF operation according to
Ton time and Toff time
OUT1
(instantaneous)
① - ③
OUT2
(time-limit)
⑥ - ⑧
ON indicator
OUT2 operation
display
OFF indicator
Rt : Return Time Ton : on operation time Toff : off operation time
Rt : Return Time T1 : out1 on operation time T2 : out2 on operation time
Toff : out1 & out2 off operation time
■ Panel cutout
9
:
#
"
• ON operation time range selection switch
Select ON operation time range in operation mode ‘A/B/D/E/F’
Select ON operation time range of OUT2 in operation mode ‘C’
Refer to the below table about
The operation mode selection switch
Output ON indicator •
Turns on when output is ‘ON’ in
operation mode ‘A/B/D/E’
Turns on when OUT2 output is ‘ON’ in
operation mode ‘C/F’
• Volume for setting ON operation time
ON operation time setting in operation mode ‘A/B/D/E/F’
Setting ON operation time of OUT2 in operation mode ‘C’
Output OFF indicator •
Turns on when output is ‘OFF’ in
operation mode ‘A/B/D/E’
Turns on when OUT1 output is ‘ON’ in
operation mode ‘C/F’
Volume for setting OFF operation time •
OFF operation time setting in
operation mode ‘A/B/D/E/F’
Setting ON operation time of OUT1 in
operation mode ‘C’
• OFF operation time range selection switch
Select OFF operation time range in operation mode ‘A/B/D/E/F’
Select the ON operation time range of OUT1 in operation mode ‘C’
* When the operating time range is selected as ‘10 S / 10 M / 10 H, 30 S
/ 30 M / 30 H, 60 S / 60 M / 60 H’, the operating time is converted to
x10’ from the display time on the front panel and is operated.
* When OFF operation time range is selected as ‘10sec / 10min / 10 H,
30 S / 30 M / 30 H, 60 S / 60 M / 60 H’, OFF operation time is converted
to 'x10' from the display time on the front panel and operates.
※ When the switch power is 'ON", both the operation time range and
the operation mode are not changed. (Ex. A -> B / 1 S -> 1 M)
Please turn off the switch power and then change it.
Operation mode selection switch (
※
change after power is off)
Indication
Output operation mode
TF62A
A
FLICKER ON START (time-limit 2c)
B
FLICKER OFF START + instantaneous 1c
C
TWIN (time-limit 1c + time-limit 1c)
D
FLICKER OFF START (time-limit 2c)
E
FLICKER ON START + instantaneous 1c
F
DUAL (time-limit 1c + time-limit 1c)
* Same as TF62D output operation of
existing product
ON/OFF operation time range selection switch (
※
change after power is off)
time range
setting time range
TF62A-1
1 S
0.1 ~ 1
sec
1 M
0.1 ~ 1
min
1 H
0.1 ~ 1
hour
10 S
1 ~ 10 sec
10 M
1 ~ 10 min
10 H
1 ~ 10 hour
TF62A-3
3 S
0.3 ~ 3
sec
3 M
0.3 ~ 3
min
3 H
0.3 ~ 3
hour
30 S
3 ~ 30 sec
30 M
3 ~ 30 min
30 H
3 ~ 30 hour
TF62A-6
6 S
0.6 ~ 6
sec
6 M
0.6 ~ 6
min
6 H
0.6 ~ 6
hour
60 S
6 ~ 60 sec
60 M
6 ~ 60 min
60 H
6 ~ 60 hour
Model
TF62A
Timer type
Analog twin timer
Power voltage
24
–
240 V a.c. 50/60 Hz or 24
–
240 V d.c. dual usage
Allowable voltage
±10 % of Power supply voltage
Power consumption
• Max. 4.1 VA (24
–
240 V a.c. 50/60 Hz)
• Max. 2 W (24
–
240 V d.c.)
Operating time range
0.1 sec ~ 60 hour
Operating time error
• Setting error: Max. ±5 % ±0.05
• Voltage error: Max. ±0.5 %
• Repetition error: Max. ±0.3 %
• Temperature error: Max. ±2 %
Return time
Max. 100 ms
External connection method
8-pin socket
Control
output
Operation mode
A/B/C/D/E/F (selected by front operating mode selector switch)
Contact
composition
• instantaneous SPDT (1c) + Time limit SPDT (1c)
• Time limit DPDT (2c) *Automatic change of contact composition according to operation mode
Contact capacity
• N.O. (250 V a.c. 3A Resistive load)
• N.C. (250 V a.c. 2A Resistive load)
Relay life
• Mechanical life: MIn. 10 million cycles
• Electrical life: Min. 20,000 cycles
(250 V a.c. 2A resistive load)
Insulation resistance
Min. 100 MΩ (500 V d.c. mega, at conductive terminal and non-charged metal which is exposed)
Dielectric strength
2000 V a.c. 60 Hz for 1 minute
(at conductive terminal and non-charged metal which is exposed)
Noise immunity
±2kV (between the power terminals, pulse width = 1 us, square wave noise by noise simulator)
Vibration resistance (durability) 10 - 55 Hz (1 minute) 0.75mm double amplitude 0.75 in each X, Y, Z direction for 2 hours
Shock resistance (durability)
300 m/s² (30G) in each X, Y, Z direction for 3 times
Operating ambient temperature
-10 ~ 55 ℃ (without condensation)
Accessories
• Fixing Bracket
• BRACKET-M (48.0 X 59.0 mm)
flush type bracket
Accessories
(separately sold)
• BRACKET-S (48.0 X 48.0 mm)
bracket for adjusting size (flush type)
• BRACKET-L (53.5 X 84.4 mm)
bracket for adjusting size (flush type)
Weight (g)
Approx. 79 g (Exposure type)
Approval
* OUT1 output operates as instantaneous output in operation mode ‘B/E’.
▍Connection diagram
퍟킫1
훊폏뻗큲
"
5*5-&
5'"$POOFDUJPOEJBHSBN$BTF-BTFSQSJOU
5'"
):4)5'"%:
5'""5'""5'""
%&4*(/&%#: $)&$,&%#: $)&$,&%#: $)&$,&%#: "11307&%#:
.0%&-
1"35/".&
%3"8*/(/0
%"5&
1"(&
/0
%"5&
3&7*4*0/3&$03%
핊짦뫃���pच
짪훊펓���쫆칺엖핂헎잖���핆솒뻲킪팒헪혾쩣핆
$&핆흫잖���쁢핆흫퐒욚핆쾒
)"/:06/(/69$P-UE
맪컮맪짪헪���킪5'"
퍟킫1
훊폏뻗큲
"
5*5-&
5"$POOFDUJPOEJBHSBN$BTF-BTFSQSJOU
5"
):4)5"%:
5""5""5""
%&4*(/&%#: $)&$,&%#: $)&$,&%#: $)&$,&%#: "11307&%#:
.0%&-
1"35/".&
%3"8*/(/0
%"5&
1"(&
/0
%"5&
3&7*4*0/3&$03%
핊짦뫃���pच
짪훊펓���쫆칺엖핂헎잖���핆솒뻲킪팒헪혾쩣핆
$&핆흫잖���쁢핆흫퐒욚핆쾒
)"/:06/(/69$P-UE
맪컮맪짪헪���킪5"
59.00
63.76
2.50
54.50
66.40
56.50
쯚않���컲���
헏푷폖
54.50
63.76
2.50
56.50
67.18
쯚않���컲���
헏푷폖
쯚않���컲���
헏푷폖
5"#"
065
065
108&3
7)[7"
78
$0/5"$5
7" 3FTJTUJWFMPBE
5*.&3
5"$"
065
065
108&3
7)[7"
78
$0/5"$5
7" 3FTJTUJWFMPBE
5*.&3
5""
065
065
108&3
7)[7"
78
$0/5"$5
7" 3FTJTUJWFMPBE
5*.&3
%&4*(/&%*/,03&"
."%&*/*/%0/&4*"
5""
065
065
108&3
7)[7"
78
$0/5"$5
7" 3FTJTUJWFMPBE
5*.&3
%&4*(/&%*/,03&"
."%&*/*/%0/&4*"
5""
065
065
108&3
7)[7"
78
$0/5"$5
7" 3FTJTUJWFMPBE
5*.&3
5""
065
065
108&3
7)[7"
78
$0/5"$5
7" 3FTJTUJWFMPBE
5*.&3
%&4*(/&%*/,03&"
."%&*/*/%0/&4*"
5'""
065
065
108&3
7)[7"
78
$0/5"$5
7" 3FTJTUJWFMPBE
5*.&3
5'""
065
065
108&3
7)[7"
78
$0/5"$5
7" 3FTJTUJWFMPBE
5*.&3
T1
T1
Rt
T2
T2
Ton
Ton
Ton
Ton
Ton
Rt
Toff
Toff
Toff
Ton
Ton
Ton
Rt
Toff
Toff
Toff
Toff
Toff
Ton
Ton
Ton
Rt
Toff
Toff
Toff
Toff
Toff
Ton
Ton
Ton
Ton
Ton
Rt
Toff
Toff
Toff
T1
T2
T1
T1
T2
Rt
Toff
Toff
Toff
[Unit:mm]
Assortment
Indication
S
M
L
Panel cutout
(+0.5 / -0)
X
45.0
45.5
51.0
Y
45.0
55.0
63.0
A
60.0
70.5
60.0
B
60.0
80.0
86.0
Type
Flush
Fixing
Product
name
BRACKET-S
BRACKET-M
BRACKET-L
BRACKET-SCO
Size 48.0 x 48.0 mm 48.0 X 59.0 mm 53.5 x 84.4 mm
Model
9
:
#
"
9
:
#
"
9
:
#
"
9
:
#
"
order
code
T38A/TF62A
BRACKET-S
T38A/TF62A
BRACKET-M
T38A/TF62A
BRACKET-L
FIXING
BRACKET SCO
※ Application of BRACKET-M (BRACKET-S/L refer to the chart below)
■ Exposure type
■ Flush type
9
:
#
"