Hanwha Vision PNM-8082VT User Manual Download Page 16

installation & connection

16_

 installation & connection

How to set up channels to monitor for installation

The camera body has a channel DIP switch, as shown in the figure.
You can change the channel of the camera using the channel DIP switches.

CH1

CH2

CH3

00

01

10

 

M

 

`

If a DIP switch is not fully On/Off, the product may malfunction. After installation, check the DIP switches at the back.

 

`

Be careful, as you will risk damaging a DIP switch if you manipulate it using a sharp tool.

 

`

Be careful, as a DIP switch may be damaged if you operate it with excessive force.

Adjusting the monitoring direction for the camera

Moving the camera module (Pan)

Tilt

Lens Rotation

 

`

Adjusting the monitoring direction

You can adjust the camera direction only when the camera is fixed on the ceiling. 
Here, moving the camera module along the rail is called "Pan", adjusting the slope of the camera module is 
called "Tilt", and rotating the camera module on the lens axis is called "Rotation".

 

- The rotation angle of Pan is -0 to +360˚ for each module.

 

- The rotation angle of Tilt is 0 to +73˚.

 

- The rotation angle of Rotation is 0˚ to +90˚.

 

J

 

`

The image can be covered up by the camera case depending on the angle.

 

`

Do not pan over the specified rotation angle. It might damage the cable leading to a product malfunction.

 

`

Methods of adjustment

1. 

After installing the camera in consideration of the direction to monitor, adjust the Pan angle along the 
bottom rail.

2. 

Adjust the horizontal angle so that the image does not appear to be reversed during rotation.

3. 

Adjust the tilt angle so that it points in the direction to be monitored.

Summary of Contents for PNM-8082VT




























Reviews: