4
English
Assembly basic kit
(see page 42)
Safety Notes
Gloves should be worn during installation to prevent crushing and cutting
injuries.
The product may only be used for bathing, hygienic and body cleaning
purposes.
Children as well as adults with physical, mental and/or sensoric impairments
must not use this product without proper supervision. Persons under the
influence of alcohol or drugs are prohibited from using this product.
Do not allow the streams of the shower touch sensitive body parts (such as your
eyes). An adequate distance must be kept between the shower and you.
The hot and cold supplies must be of equal pressures.
Electrical connection
The electrical connection may only be carried out by an electrician!
Pre-install voltage supply 100-240V/N/PE/50-60Hz (length: 0,3).
The system must be protected via a leakage current protective device (RCD/ FI)
with a measurement difference current of ≤ 30 mA.
The product must be connected to 4 mm² equipotential bonding (PA) to be
provided by the customer.
Electrician
The installation and testing work must be performed by a skilled electrician in
observance of VDE 0100 part 701 and IEC 60364-7-701 as well as
EN 60335-2-105.
The mains connection line must be inserted into
the connection socket with
double insulation
Z
.
Installation Instructions
• Prior to installation, inspect the product for transport damages. After it has been
installed, no transport or surface damage will be honoured.
• The pipes and the fixture must be installed, flushed and tested as per the
applicable standards.
• The plumbing codes applicable in the respective countries must be observed.
• During installation of the product by qualified trained personnel, make sure that
the entire fastening surface is even and smooth (no protruding seams or tile
offset), that the finish of the wall is suitable to apply the product and has no
weak points.
• Observe all current and water lines when drilling!
• The performance of the waste must be of sufficient size.
• The shower may only be connected downstream of a shut-off valve or sanitary
fitting.
• The product is not designed to be used with steam baths!
Technical Data
Operating pressure in front of the shower fitting:
max. 1 MPa
Recommended operating pressure:
0,3 - 0,5 MPa
(1 MPa = 10 bar = 147 PSI)
Hot water temperature:
max. 60°C
Recommended hot water temp.:
42°C
safety lock:
40°C
Warning: Exceeding this temperature can cause burns!
Thermal disinfection:
70°C / 4 min
Nominal voltage
100-240V AC 50-60Hz
Nominal consumption
18 W
Lights 4 x LED:
12V DC SELV 4 W
The lamp cannot be dimmed.
Protection class
II
Protection category
IPX5
The product is exclusively designed for drinking water!
Symbol description
Do not use silicone containing acetic acid!
Dimensions
(see page 32)
Montagebeispiele
(see page 34)
Spare parts
(see page 50)
Service Replace illuminant
(see page 54)
Cleaning
(see page 51)
Electrician
Maintenance
(see page 55)
The proper function of this protective device must be checked at regular intervals.
Water connection DN20 Warm water
Water connection DN20 Cold water
Shut off valve
Quattro 4-Way Diverter Valve
Trio 2-Way Diverter Valve with integrated Shut-off valve
Thermostatic mixer HighFlow
The waste drain performance must be more than 50 l/min.
Waste
Center shower tub
Water on / off
Wiring conduit for power supply cable
Hot surface!
Safety gloves must be worn
Eye protection must be worn
natural sponge
Decalcifier
(Citric acid base)
Avoid contact with eyes and skin. If this product
contacts your eyes, rinse thorougly with water.
Electricity on / off
Operation
(see page 50)
Disposal of waste batteries and old Electrical &
Electronic Equipment
(applicable in the European Union
and other European countries with separate collection
systems).
This symbol on the battery, the product or the packaging indicates that the battery
or the product shall not be treated as household waste. By ensuring the battery or
product are disposed of correctly, you will help prevent potentially negative
consequences for the environment and human health. The recycling of the
materials will help to conserve natural resources. To ensure that the battery or
product will be treated properly, hand over the product at end-of-life to the applica-
ble collection point for the recycling of batteries, electrical and electronic
equipment. For more detailed information about recycling of this product or
battery, please contact your local Civic Office, your household waste disposal
service or the shop where you purchased the product.
i
Quattro
Trio
High
Flow
> 50 l/min
Raindrain
X
Assembly Finish set
(see page 47)
Summary of Contents for Rainmaker 2841418 Series
