Hans Grohe Rainfinity Showerpipe 360 1jet 26842 7..., Instructions For Use/Assembly Instructions

Page: 2 / 12

2
中文
安装
(参见第页
5
)
安全技巧
装配时为避免挤压和切割受伤，必须戴上手套。
本产品只允许作为洗浴、卫生和洁身之用。
头顶花洒夹持杆只为夹持头顶花洒而设计，不得让其承载其它物品！
不得让儿童和肢体、精神和
/
或意识有障碍的成人在不受监管的情况下
使用淋浴系统。受酒精或毒品影响的人员不得使用淋浴系统。
必须避免让身体敏感部位（如眼睛）接触到莲蓬头喷水。必须保持莲
蓬头与人头之间有足够的距离。
该产品不得作扶柄使用。必须安装单独的扶柄。
安装提示
•
安装前必须检查产品是否受到运输损害。 安装后将不认可运输损害或
表面损伤。
•
管道和阀门必须根据通用标准进行安装、冲洗和检查。
•
请遵守当地国家现行的安装规定。
•
本安装说明中所规定的安装尺寸理想用于身高
1800 mm
左右的人士。
尺寸可根据需要进行修改。在这种情况下，您必须留意，如果安装高
度改变，则花洒到地板的最小高度也随之改变，且必须考虑到连接尺
寸的改变。
•
由有资格的专业人员进行产品安装时请注意：在所有加固区域中，加
固表面是否平整（无突出的接缝或瓷砖），墙体结构是否适合产品安
装且未显露出任何缺点。
•
必须装上花洒所附带的滤柱式过滤网，以过滤管道里的杂质污物。杂
质污物会影响花洒的功能和
/
或损坏花洒的功能部件，由此而产生的产
品损坏不属于汉斯格雅的保修范围。
•
本产品并非设计来与蒸气浴连接使用！
技术参数
工作压强： 最大
0,6 MPa
推荐工作压强：
0,35 - 0,4 MPa
(
1 MPa = 10 bar = 147 PSI
)
热水温度： 最大
60°C
热力消毒
:
最大
70°C / 4
分钟
•
自动防止回流
•
该产品专为饮用水设计！
符号说明
请勿使用含有乙酸的硅胶！
保养 (参见第页
11
)
•
单向阀必须在符合国家或当地的法律的情况下按照
DIN EN 1717
定期检
查（至少一年一次）。
大小 (参见第页
3
)
安装实例 (参见第页
4
)
流量示意图 (参见第页
4
)
备用零件 (参见第页
9
)
XX =
颜色代码
00 =
镀铬
70 = Matt White
选装附件 (不在供货范围内)
匹配瓷砖的圆盘
#93773XXX
(参见第页
9
)
清洗 (参见第页
10
)
操作 (参见第页
12
)
i
English
Assembly (see page 5)
Safety Notes
Gloves should be worn during installation to prevent crushing and cutting
injuries.
The product may only be used for bathing, hygienic and body cleaning
purposes.
The arm of the shower head is intended only to hold the shower head. Do not
load it down with other objects!
Children as well as adults with physical, mental and/or sensoric impairments
must not use this product without proper supervision. Persons under the
influence of alcohol or drugs are prohibited from using this product.
Do not allow the streams of the shower touch sensitive body parts (such as your
eyes). An adequate distance must be kept between the shower and you.
The product may not be used as a holding handle. A separate handle must be
installed.
Installation Instructions
• Prior to installation, inspect the product for transport damages. After it has been
installed, no transport or surface damage will be honoured.
• The pipes and the fixture must be installed, flushed and tested as per the
applicable standards.
• The plumbing codes applicable in the respective countries must be observed.
• The installation dimensions stated in these installation instructions are ideal for
people of approximately 1800 mm in body height. The dimensions can be
altered if required. In this case, pay attention to the fact that a change of
installation height will also change the minimum height, and that the altered
mounting dimensions must be taken into consideration.
• During installation of the product by qualified trained personnel, make sure that
the entire fastening surface is even and smooth (no protruding seams or tile
offset), that the finish of the wall is suitable to apply the product and has no
weak points.
• The filter insert must be use to protect the shower against incoming dirt by
pipework. Incoming dirt leads to defects or/and can damage parts of the
shower; such caused faults voids all liability and guarantee claims.
• The product is not designed to be used with steam baths!
Technical Data
Operating pressure: max. 0,6 MPa
Recommended operating pressure: 0,35 - 0,4 MPa
(1 MPa = 10 bar = 147 PSI)
Hot water temperature: max. 60°C
Thermal disinfection: max. 70°C / 4 min
• Safety against backflow
• The product is exclusively designed for drinking water!
Symbol description
Do not use silicone containing acetic acid!
Maintenance
(see page 11)
• The check valves must be checked regularly according to DIN EN 1717 in
accordance with national or regional regulations (at least once a year).
Dimensions (see page 3)
Installation example
(see page 4)
Flow diagram (see page 4)
Spare parts
(see page 9)
XX = Colors
00 = Chrome Plated
70 = Matt White
Special accessories (order as an extra)
tile-matching-disk #93773XXX (see page 9)
Cleaning (see page 10)
Operation
(see page 12)
i