ADS17500
IMPORTANT!! PLEASE READ ENTIRE INSTRUCTION SHEET BEFORE ASSEMBLY!!
TO EXPEDITE ANY FUTURE WARRANTY CLAIMS, PLEASE KEEP INSTRUCTION SHEET, WARRANTY CARD AND RECEIPT
FRONT SEAT
SUPPORT BAR
Fig.1
B
C
F
Fig.3
D
E
FOOT CAP
FOOT CAP
PARTS LIST
PARTS LIST
DESCRIPTION
DESCRIPTION
ORDER PART #
ORDER PART #
SEAT FRAME
BOLT COVER
HW0022
FC0030
FOOT CAP
FACTORY ASSEMBLY
SEAT BASE
1/4" X 35 MM
BOLT
1/4" X 45 MM
BOLT
Ø6.5 X 1.0 MM
WASHER
HW0142
HW0040
HW0004
QTY
QTY
1
A
B
C
D
E
F
G
1
2
2
2
2
1
HW0252
Fig.2
IMPORTANT NOTE: Your sling seat may appear to be slightly warped. This is not unusual.
Proper assembly procedure will straighten out the sling seat in the frame. There are four bolts
used to attach the seat frame to the seat base. After inserting all the bolts, each of these bolts
must be tightened a few revolutions at a time in rotation.
Step 1:
Identify all parts packed in the carton against the parts list. Remove all protective
materials. Set parts on a flat, non-abrasive surface to avoid scratching. If you are missing
any parts or are unsure how to proceed with assembly, call our Customer Service Center
immediately at 1-800-416-3511.
Do not attempt to assemble chair if any parts are
missing or damaged.
IMPORTANT NOTE: Assembling this chair requires attaching the sling seat frame to the seat
base. We recommend two people work together to assemble the chair since it is critical that all
the holes in the seat frame are aligned exactly with the holes in the seat base. All bolts need to
be inserted and tightened into the fixed nuts in a straight and direct path. Inserting the bolts at
even the slightest angle could strip the nuts and bolts, damaging the entire chair.
Step 2:
Working from behind the chair, have another person stand in front of the chair and position
the sling seat frame in between the arms of the seat base as shown in
Fig.1
so that the holes
on both sides of the upper portion of the seat frame back align with the fixed nut holes in
the seat base.
Step 3:
Working from the front of the chair, add a washer to a 1/4"x45 mm bolt. From the
underside of the front seat support bar, insert the bolt with washer through one of the holes
in the seat support bar, into the fixed nut inside the lower front portion of the seat base as
shown in
Fig.2
.
Hand tighten 3-4 revolutions only. Do not tighten Completely.
Repeat
for opposite side of chair.
Step 4:
From behind the chair, insert a 1/4"x35 mm bolt through the back arm portion of the seat
base and into the fixed nut in the seat frame as shown in
Fig.3
. Make sure the bolt is
inserted exactly straight!
Hand tighten 3-4 revolution only. Do not tighten completely.
Repeat for opposite side of chair.
Step 5:
Tighten all bolts with the hex bolt driver. Each bolt must be tightened a 3-4 revolutions
only at a time. Begin with top left bolt. Move to bottom right bolt then to top right bolt,
followed by bottom left bolt. Repeat this "X" pattern until all bolts are tight.
Do not over
tighten bolts
. Over tightening may strip bolts or nuts, damaging the entire chair. Cover
1/4"x35 mm bolts with bolt covers.
Step 6:
Examine the chair from the front. If the sling seat does not appear tight or straight in the
seat base, repeat steps 3, 4 and 5. If you do not feel your chair is assembled properly, or
you have any questions, call our Customer Service Center at 1-800-416-3511.
IMPORTANT NOTE: Damage to welds or frames resulting from over tightened bolts or
improper assembly is not covered under our warranty. Please read all instructions carefully
before assembly. If you have any questions regarding your assembly, call our Customer
Service Center at 1-800-416-3511.
* NOTE: PARTS SHOWN ON PARTS LIST ARE NOT TO SCALE
HEX BOLT DRIVER
A
SLING TUBE CAP
FACTORY ASSEMBLY
FC0358
AN0523
AN0524
