1
PROJECTOR ON/OFF BUTTON
14
DISPLAY
2
PROJECTOR 180° FLIP BUTTON
15
AL1 BUZZER INDICATOR
3
MIN/
BUTTON
16
AL1 RADIO INDICATOR
4
HOUR/
BUTTON
17
AL2 BUZZER INDICATOR
5
DIMMER BUTTON
18
AL2 RADIO INDICATOR
6
AL2/VOL
−
BUTTON
19
PM INDICATOR
7
AL1/VOL
+
BUTTON
20
DC IN JACK
8
CLK/MEM BUTTON
21
AUX-IN JACK
9
SNOOZE/SLEEP BUTTON
22
USB CHARGING PORT
10
/
SOURCE/AL.OFF BUTTON
23
FM ANTENNA
11
PROJECTOR WHEEL
24
BATTERY COMPARTMENT
12
PROJECTOR LENS
25
SPEAKER
13
PROJECTION FOCUS KNOB
CONNECTING THE UNIT TO POWER
Plug one end of the AC adaptor into the DC power Input, and then plug the other end into AC wall outlet. Before switching
on the unit, make sure that the voltage of your electricity supply is the same as that indicated on the rating plate.
BATTERY BACKUP
Insert two pieces UM-4 batteries into the battery compartment. Be sure to observe the proper polarity (the "+" and "-" signs)
as indicated inside the battery compartment.
In case of power failure or interrupted AC power, the current time and alarm time settings, the stored radio stations are
preserved in the memory of the unit by means of battery back-up function.
SETTING THE CLOCK
1. When the unit is OFF, press and hold the CLK/MEM button for about 1 second, the time will begin to flash on the LED
display.
2. Press the HOUR/
/ button to adjust the hour.
3. Press the MIN/
button to adjust the minute.
4. When the correct time is selected, press the CLK/MEM button again to confirm.
SETTING THE ALARMS
1. When the unit is OFF, press the AL1/VOL+ or AL2/VOL− button. The ALARM time will begin to flash on the LED display.
2. Press the HOUR/
button to adjust the alarm hour.
3. Press the MIN/
button to adjust the alarm minute.
4. When the correct time is selected, press the AL1/VOL+ or AL2/VOL− button to confirm.
5. Press the AL1/VOL+ or AL2/VOL− button to select the ALARM sound mode - buzzer or currently set radio station. The
alarm buzzer or radio indicator will light up.
- 3 -
SNOOZE FUNCTION
1. Whenever the alarm (radio or buzzer) activates, it can be temporarily suspended for a short period of 9 minutes by
pressing the SNOOZE/SLEEP button once.
2. The buzzer or radio will then automatically activate again after the 9 minutes SNOOZE period has ended.
3. This procedure can be repeated for up to approximately one hour.
TURN OFF THE ALARM
When the Alarm activate, press the
/SOURCE/AL.OFF button to turn off the Alarm.
LISTENING TO THE FM RADIO
1. Press the
/SOURCE/AL.OFF button to select FM radio mode.
2. Press the HOUR/
button or MIN/
button step by step to tune to the desired radio stations.
3. Press and hold the HOUR/
button or MIN/
buttons for approx. 1 second, it will start to search the next radio station
in the direction of the search. The search operation simply finds stations with strong signals. Stations with weak
reception can only be tuned in manually.
ANTENNA
For best reception, fully extend the FM wire antenna to receive FM stations.
SAVING A RADIO STATION TO THE MEMORY
1. Tune the radio to the desired station.
2. Press and hold the CLK/MEM button for approx. 1 second, the LED display will show P01 and flash, the radio station
will stored in the memory..
3. Up to 10 FM radio stations can be stored in the memory.
TO LISTEN TO A SAVED RADIO STATION
1. Press the
/SOURCE/AL.OFF button to select FM radio model
2. Press the CLK/MEM button to select the stored radio station.
SLEEP TO MUSIC FUNCTION
1. This function allows you to listen to the radio while you fall asleep.
2. Press the SNOOZE/SLEEP button, the display will show the default sleep time of 90 minutes
3. Press the SLEEP button again to adjust the desired sleep time.
4. The options are 90-80-70-60-50-40-30-20-10-min. or OFF
5. Now you can enjoy listening to the radio for the pre-set period of sleep time.
6. After this pre-set time has elapsed, the unit will switch off automatically.
AUX IN CONNECTION
1. Insert one side of the audio cable (requires 3.5mm stereo plug, not supplied) into the line-out jack or phones jack on
your MP3 player or audio device and the other side to the aux-in jack on the unit.
2. Press the
/SOURCE/AL.OFF button to select AUX mode, AUX will display in the LED display for a few seconds.
3. Turn on your MP3 player and follow the playback instruction.
4. To stop this function, simply turned off your MP3 player.
CHARGE YOUR DEVICES
Connect the standard size end of a USB cable (not included) to the USB port on the unit and connect the other end to the
charging port of your device. The unit contains one USB port with 5V ~ 1A charging.
Remarks:
Some devices may not support USB charging or may require a higher power rating than this product provides.
Observe the charging status on your device. Ensure your device is working properly before attempting to charge. Charging
function may not be supported for all phones or electronic devices
PROJECTION
1. Press the PROJECTION ON/OFF button to turn on the PROJECTION function.
2. The projector displays the time via a bright red projection light onto a wall, ceiling or any surface for viewing in a
darkened room.
3. Rotate the Projector wheel to point the Projector lens to the desired direction. The projector lens can vertically swivel
180° so that you may view the TIME from different position. .
4. If the projected image is out of focus, use the PROJECTION FOCUS knob to adjust the image until the projection is in
focus.
5. To turn off the PROJECTION function, press the PROJECTION ON/OFF button again.
Notes
1. Do not stare into the lens directly.
2. The projector function cannot be used unless the clock has been set.
3. Certain walls and ceilings may not display the projection properly.
4. Don’t rotate the projector wheel beyond its limits, it may be damaged.
- 4 -
