manualshive.com logo in svg

Hanna Instruments HI99162, Instruction Manual, Page: 17 / 20

Share
Download
Hanna Instruments HI99162 Instruction Manual Download Page 17

17

ELECTRODE MAINTENANCE

ELECTRODE MAINTENANCE

PREPARATION

•  Remove the protective cap. Do not be alarmed if any salt 

deposits are present. 

Rinse with water.

•  Shake the electrode down as you would do with a 

clinical thermometer to eliminate any air bubbles inside 
the glass tip. 

•  Remove the fill hole cover to ensure the reference junctions 

are flowing. Set aside for storage.

•  Top off the electrolyte filling solution using 

HI7082

 

solution.

•  If the glass tip and/or junction are dry, soak the 

electrode in 

HI70300

 Storage Solution for a minimum 

of 30 minutes.

•  Rinse with water.

•  Calibrate before using.

STORAGE

•  To ensure a quick response, the glass tip and the junction 

should be kept moist and not allowed to dry. 

•  Replace protective cap with a few drops of 

HI70300

 

Storage Solution. Follow PREPARATION above before 

taking measurements.

• Replace the fill hole cover.

Note: Never store the electrode in distilled water

PERIODIC MAINTENANCE 

•  Inspect the electrode for any scratches or cracks. If any 

present, replace the electrode.

•  Rinse off any salt deposits with water.

•  Follow the STORAGE procedure above.

CLEANING PROCEDURE

•  Soak in Hanna 

HI7061

 general cleaning solution 

or 

HI700640 

cleaning solution for milk deposits for 

20 minutes. Rinse with water.

•  Soak the electrode in 

HI70300

 Storage Solution for a 

minimum of 30 minutes. Rinse with water. Calibrate 

before using.

TROUBLESHOOTING

•  pH Meter: Follow the meter’s operating and calibration 

procedures.

•  Electrode: Evaluate your electrode performance based on 

the 

Sensor check

 procedure on page 13.

Summary of Contents for HI99162





















Reviews:

No comments