Required Accessories
HI93738-01
Reagents for 100 tests
HI93738-03
Reagents for 300 tests
Other Accessories
HI96738-11
CAL Check™
Standard Cuvettes (1 set)
HI740029P
9V battery (10 pcs.)
HI731318
Tissue for wiping cuvettes (4 pcs.)
HI731331
Glass cuvettes (4 pcs.)
HI731335
Caps for cuvettes (4 pcs.)
HI93703-50
Cuvettes cleaning solution (230 mL)
ACCESSORIES
HI96738
is warranted for two years against defects in workmanship and
materials when used for its intended purpose and maintained according to
the instructions.
This warranty is limited to repair or replacement free of charge.
Damages due to accident, misuse, tampering or lack of prescribed maintenance
are not covered.
If service is required, contact your local Hanna Instruments Office. If under
warranty, report the model number, date of purchase, serial number and the
nature of the failure. If the repair is not covered by the warranty, you will be
notified of the charges incurred.
If the instrument is to be returned to Hanna Instruments, first obtain a Returned
Goods Authorization Number from the Customer Service Department and then
send it with shipment costs prepaid. When shipping any instrument, make sure
it is properly packaged for complete protection.
To validate your warranty, fill out and return the enclosed warranty card within
14 days from the date of purchase.
WARRANTY
IST96738 01/18
Hanna Instruments reserves the right to modify the design, construction, or
appearance of its products without advance notice.
All rights are reserved. Reproduction in whole or in part is prohibited without the
written consent of the copyright owner, Hanna Instruments Inc., Woonsocket,
Rhode Island, 02895, USA
1.
GLP/
key: press to enter GLP mode. In calibration mode press to edit
the date and time.
2.
CAL CHECK
key: press to perform the validation of the meter, or press
and hold for three seconds to enter calibration mode.
3.
ZERO/CFM
key: press to zero the meter prior to measurement, to
confirm edited values or to confirm factory calibration restore.
4.
READ
key: In measurement mode, press to make a measurement.
In GLP mode press to view the next screen.
5.
ON/OFF
key: to turn the meter on and off.
6. Liquid Crystal Display (LCD)
7. Cuvette alignment indicator
8. Cuvette holder
Please examine this product carefully. Make sure that the instrument is not
damaged. If any damage occured during shipment, please contact your local
Hanna Instruments Office.
Each
HI96738
Ion Selective Meter is supplied complete with:
• Sample Cuvettes and Caps (2 pcs.)
• 9V Battery
• Instruction Manual
• Quality Certificate
Note: Save all packing material until you are sure that the instrument
works correctly. Any defective item must be returned in its original
packing.
1. The measuring scheme (lamp, cuvette, detector), appears during
different phases of zero or reading measurement
2. Error messages and warnings
3. The battery icon indicates the charge state of the battery
4. The hourglass appears when an internal check is in progress
5. Status messages
6. The chronometer appears when the reaction timer is running
7. The month, day and date icons appear when a date is displayed
8. Four digit main display
9. Measuring units
10. Four digit secondary display
Thank You
Thank you for choosing a Hanna Instruments product. Please read
this instruction manual carefully before using the instrument.
For more information about Hanna Instruments and our
products, visit www.hannainst.com.
For technical support, contact your local Hanna Instruments
Office or e-mail us at [email protected]
Find your local Hanna Instruments Office at www.hannainst.com
PRELIMINARY EXAMINATION
For more details about spare parts and accessories see
“Accessories”.
SPECIFICATIONS
Range
0.00 to 2.00 mg/L
Resolution
0.01 mg/L
Accuracy
@25
°
C (77
°
F)
±0.10 mg/L ±5% of reading
Light source
Tungsten Lamp
Light Detector
Silicon Photocell with narrow band interference
filter @575 nm
Method
Adaptation of the Chlorophenol Red method. The
reaction between chlorine dioxide and reagents
causes a colorless to purple tint in the sample.
Environment
0 to 50
°
C (32 to 122
°
F);
max 95% RH non-condensing
Battery Type
9V (1 pc.)
Auto-Shut off
After 10’ of non-use in measurement mode;
after 1 hour of non-use in calibration mode;
with last reading reminder
Dimensions
192 x 104 x 69 mm (7.6 x 4.1 x 2.7”)
Weight
320 g (11.3 oz.)
DISPLAY ELEMENTS DESCRIPTION:
FUNCTIONAL DESCRIPTION
Light High:
There is too much light to perform
a measurement. Please check the preparation of
the zero cuvette.
Light Low:
There is not enough light to perform
a measurement. Please check the preparation of
the zero cuvette.
No Light:
The instrument cannot adjust the
light level. Please check that the sample does
not contain any debris.
During calibration procedure:
On zero reading:
On sample reading:
ERRORS AND WARNINGS
Other errors and warnings:
Cap error:
Appears when external light enters
in the analysis cell. Assure that the cuvette cap
is present.
Battery low:
The battery must be replaced soon.
Dead battery:
This indicates that the battery is
dead and must be replaced. Once this indication
is displayed, normal operation of the instrument
will be interrupted. Change the battery and restart
the meter.
HI9
37
38
B-0
1•
Turn the meter on by pressing
ON/OFF
.
2•
When the beeper sounds briefly and the
LCD displays dashes, the meter is ready.
The blinking
“ZERO”
indicates that the
instrument needs to be zeroed first.
3•
Fill two graduated mixing cylinders (#1
& #2) up to the 25 mL mark with the
sample.
4•
Add 0.5 mL of
HI93738A-0
Reagent A to
each cylinder (#1 & #2), close them and
invert several times to mix.
5•
Add the content of one packet of
HI93738B-0
Reagent B to only one of
the two cylinders (#1), close it and invert
several times to mix. This is the blank.
6•
Add precisely 0.5 mL of
HI93738C-0
Reagent C to each cylinder (#1 & #2),
close them and invert several times to mix.
7•
Add 0.5 mL of
HI93738D-0
Reagent D to
each cylinder (#1 & #2), close them and
invert several times to mix. Cylinder 2 is the
sample.
8•
Fill a cuvette up to the 10 mL mark with
blank (#1) and replace the cap.
9•
Place the blank (#1) into the holder
and ensure that the notch on the cap is
positioned securely into the groove.
10•
Press
ZERO/CFM
and the lamp, cuvette and
detector icons will appear on the display,
depending on the measurement phase.
After a few seconds the display will show
“-0.0-”
. The meter is now zeroed and ready
for measurement.
11•
Fill a cuvette up to the 10 mL mark with
the reacted sample (#2) and replace the
cap.
12•
Insert the sample into the instrument
and ensure that the notch on the cap is
positioned securely into the groove.
13•
Press
READ
and the display will show
the lamp, cuvette and detector icons,
depending on the measurement phase.
At
the end of measurement, the instrument
directly displays concentration in mg/L of
chlorine dioxide on the LCD.
2
8
HI93738A-0
5
6
HI93738C-0
HI93738D-0
7
4
3
9
MEASUREMENT PROCEDURE
Measurement
10
#1
11
#2
SAMPLING PROCEDURE:
It is recommended to analyze chlorine dioxide
samples immediately upon collection. Chlorine
dioxide samples must be stored in dark, glass
stoppered bottles, with minimal head space.
Excessive heat (greater than 25 °C / 78 °F),
agitation and exeposure to light must be
avoided.
INTERFERENCES
:
Interference may be caused by strong oxidants.
12
13
Standard Low:
The standard reading is less
than expected.
Standard High:
The standard reading is higher
than expected.
Inverted cuvettes:
The sample and the zero
cuvette are inverted.
Zero:
A zero reading was not taken. Follow the
instructions of the measurement procedure for
zeroing the meter.
Under range:
A blinking
“0.00”
indicates
that the sample absorbs less light than the zero
reference. Check the procedure and make sure
you use the same cuvette for reference (zero)
and measurement.
Over Range:
A flashing value of the maximum
concentration indicates an over range condition.
The concentration of the sample is beyond the
programmed range: dilute the sample and
re-run the test.
Cooling lamp:
The instrument waits for the
lamp to cool down.
