Hanna Instruments HI96707 Instruction Manual Download Page 5

5

The 

HI96707

 is an auto diagnostic portable microprocessor meter that benefits from Hanna 

Instruments’ years of experience as a manufacturer of analytical instruments. It has the advanced 
optical system based on a special Tungsten Lamp and a narrow band interference filter that allows 
most accurate and repeatable readings. All instruments are factory calibrated and the electronic 
and optical design minimizes the need of frequent calibration.
With the powerful 

CAL Check

TM

 validation function, you are able to validate good performance 

of your instrument at any time. The validation procedure is extremely user friendly. Just use the 
exclusive Hanna Instruments ready‑made, NIST traceable standards to verify the performance of 
the instrument and recalibrate if necessary.
All instruments are splash proof and the lamp and filter units are protected from dust or dirt by 
a transparent cup. This makes the instruments fulfill field applications. Display messages aid the 
user in routine operation. The meter has an auto‑shut off feature that will turn off the instrument 
after 10 minutes of non use in measurement mode or after 1 hour if left in calibration mode.
The meter uses an exclusive positive‑locking system to ensure that the cuvette is in the same 
position every time it is placed into the measurement cell. It is designed to fit a cuvette with a 
larger neck making it easier to add both sample and reagents. The cuvette is made from special 
optical glass to obtain best results.
The 

HI96707

 meter measures the Nitrogen‑Nitrite (N0

2

‑N) content in the samples in the 0.000 

to 0.600mg/L (ppm) range, in drinking, surface and saline water samples and in domestic and 
industrial wastes. The method is an adaptation of an EPA approved method.
The reagent is in

 

powder form and it is supplied in packets. The amount of reagent is precisely 

dosed to ensure the maximum repeatability.

degree Celsius 
degree Fahrenheit
milligrams per liter. mg/L is equivalent to ppm (parts per million)
milliliter
millivolt
American Society for Testing and Materials

°C

:

°F

:

mg/L

:

mL

:

mV

:

ASTM

:

GENERAL DESCRIPTION

ABBREVIA

TIONS

Summary of Contents for HI96707





























Reviews: