manualshive.com logo in svg

Hanna Instruments HI 8510, Instruction Manual

Share
Download
Hanna Instruments HI 8510 Instruction Manual Download Page 56

54

Follow the Preparation Procedure above be-
fore taking measurements.

Note: NEVER STORE THE ELECTRODE IN

DISTILLED WATER OR DRY.

PERIODIC  MAINTENANCE

Inspect the electrode and the cable. The cable
used for the connection to the meter must be
intact and there must be no points of broken
insulation on the cable or cracks on the elec-
trode stem or bulb.

Connectors must be perfectly clean and dry.
If any scratches or cracks are present, re-
place the electrode. Rinse off any salt depos-
its with water.

For refillable electrodes:

Refill the electrode with fresh electrolyte
(HI7071 for single junction or HI 7082 for double
junction electrodes). Allow the electrode to
stand upright for 1 hour.
Follow the Storage Procedure above.

CLEANING  PROCEDURE

General

Soak in Hanna HI 7061 General
Cleaning Solution for approxi-
mately 1 hour.

Removal of films, dirt or deposits on the mem-
brane/junction:

Protein

Soak in Hanna HI 7073 Protein
Cleaning Solution for 15 min-
utes.

Inorganic

Soak in Hanna HI 7074 Inor-
ganic Cleaning Solution for 15
minutes.

Oil / grease

Rinse with Hanna HI 7077 Oil
and Fat Cleaning Solution.

Summary of Contents for HI 8510







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands