Dear Customer,
Thank you for choosing a Hanna Instruments
®
product. Please read this instruction manual carefully
before using the instrument. For more information about Hanna Instruments and our products, visit
www.hannainst.com or e-mail us at [email protected].
For technical support, contact your local Hanna Instruments office or e-mail us at [email protected].
Preliminary Examination
Remove the
HI98509
Checktemp
®
1 and accessories from the packing material and examine it carefully. If you
require any further information, please contact Hanna Instruments technical support team at [email protected].
HI98509
is supplied with: 1.5V AAA battery (3 pcs.), meter stand, and Instruction manual with instrument
quality certificate printed on the back.
General Description & Intended Use
HI98509
is a high-accuracy thermometer connected to a stainless steel probe by a 1 m (3.3’) flexible,
silicone cable. The probe incorporates an NTC thermistor sensor, providing accurate temperature
measurements compliant with HACCP requirements. Lightweight and easy to clean the sharp-tip penetration
probe, is ideal for checking the temperature of semi-solid products such as fruit, vegetable, and cheese. This
probe can also handle measurements in liquid, air, and frozen materials.
Specifications
Range
−50.0 to 150.0 °C ; −58.0 to 302.0 °F
Resolution
0.1 °C (−50.0 to 150.0 °C); 0.1 °F (−58.0 to 199.9 °F) / 1 °F (above 200 °F)
Accuracy
±0.2 °C (−30.0 to 120.0 °C); ±0.3 °C (outside: −50.0 to −30.0 °C and 120.0 to 150.0 °C)
±0.5 °F (−22.0 to 199.9 °F); ±1 °F (outside: −58.0 to −22.0 °F and 200.0 to 302.0 °F)
Probe
AISI 316 stainless steel with 1 m (3.3’) silicone cable
Battery type / life 1.5V AAA / approximately 2 years of use
Auto shut-off
8 min. (default), 60 min. or OFF
Environment
−30 to 50 °C (−22 to 122 °F); IP65
Dimensions
107 x 59 x 17 mm (4.2 x 5.3 x 0.7“)
Weight
130 g (4.6 oz.)
Certification
EN13485; suitability: storage
Climatic environment: E; accuracy class: 0.5
Operation
Press the
ON/OFF
button to turn the thermometer on.
CAL Check™ automatically verifies the thermometer’s circuit accuracy at 0.0 °C.
During start up, the calibration of the instrument’s circuit is checked and the result is briefly displayed to
show the calibration result.
“
CAL
” and “
-0-
” indicate that the instrument performs within specifications.
“
Err
” displayed during measurement indicates that the user has to wait for the reading to stabilize.
Note:
The CAL Check system can only check the electronic circuit calibration and does not check the sensor
of the Checktemp 1. It is recommended to check the sensor by performing an ice test or comparative test
against a reference thermometer.
Meter Setup
Remove the battery cover to find the
SET
button located inside.
Press
SET
button once for temperature unit selection and twice for auto shut-off selection. With current
temperature unit displayed:
• Press the
ON/OFF
button to select “
°C
” or “
°F
”. Press the
SET
button once to save.
• Press the
ON/OFF
button to navigate Auto shut-off options: 8 minutes (“
d08
”, default), 60 minutes
(“
d60
”), OFF (“
d--
”). Press the
SET
button once to save.
All rights are reserved. Reproduction in whole or in part is prohibited without the written consent of the copyright owner,
Hanna Instruments Inc., Woonsocket, Rhode Island, 02895, USA.
IST98509 09/21
Battery Replacement
When the battery symbol is displayed blinking, or the thermometer does not turn on, batteries need to be
replaced. To replace the batteries:
1. Remove the four screws on the back of the instrument to open the battery compartment.
2. Remove the old batteries.
3. Insert three new 1.5V AAA batteries in the battery compartment while paying attention to the correct
polarity. Do not mix old and new Alkaline batteries.
4. Close the battery compartment using the four screws.
Note:
Only use the battery type specified in this instruction manual. Old batteries should be disposed of in
accordance with local regulations.
Certification
All Hanna Instruments conform to the
CE European Directives.
Disposal of Electrical & Electronic Equipment.
The product should not be treated as household waste.
Instead, hand it over to the appropriate collection point for the recycling of electrical and electronic
equipment, which will conserve natural resources.
Disposal of waste batteries.
This product contains batteries, do not dispose of them with other household
waste. Hand them over to the appropriate collection point for recycling.
Ensuring proper product and battery disposal prevents potential negative consequences for the environment
and human health. For more information, contact your city, your local household waste disposal service,
or the place of purchase.
Recommendations for Users
Before using this instrument, make sure that it is entirely suitable for your specific application and for
the environment in which it is used. Any variation introduced by the user to the supplied equipment
may degrade the instrument’s performance. For your and the instrument’s safety do not use or store the
instrument in hazardous environments.
Warranty
HI98509
Checktemp 1 is warranted for a period of one year against defects in workmanship and materials
when used for its intended purpose and maintained according to instructions. This warranty is limited to
repair or replacement free of charge. Damage due to accidents, misuse, tampering, or lack of prescribed
maintenance is not covered. If service is required, contact your local Hanna Instruments office. If under
warranty, report the model number, date of purchase, serial number, and the nature of the problem. If the
repair is not covered by the warranty, you will be notified of the charges incurred. If the instrument is to be
returned to Hanna Instruments office, first obtain a Returned Goods Authorization (RGA) number from the
Technical Service department and then send it with shipping costs prepaid. When shipping any instrument,
make sure it is properly packaged for complete protection.
Hanna Instruments reserves the right to modify the design, construction, or appearance of its products without
advance notice.
ON/OFF
button
SET
button
Silicone cable
Liquid Crystal
Display
Temperature
probe
Meter stand
Maximum
Immersion
Level
Recommended
Immersion Level
4 cm (1.5”)