manualshive.com logo in svg

Hangar 9 Twist 3D .40, Assembly Manual, Page: 22 / 40

Share
Download
Hangar 9 Twist 3D .40 Assembly Manual Download Page 22

22

Section 9: Throttle Pushrod Installation

Step 3

Slide a clevis retainer onto a nylon clevis. Thread a
clevis onto a 14

5

/

8

" wire, a minimum of 10 turns.

Step 4

Attach the clevis to the throttle arm on the
carburetor. Slide the pushrod wire into the pushrod
tube and re-install the engine. Bend the pushrod if
necessary so it moves freely.

Section 10: Fuel Tank Assembly

Required Parts

• Clunk (fuel pickup)

• Metal caps (2)

• Fuel pickup tubing

• Fuel tank

• Rubber stopper

• M3 x 20 screw

• Metal tube (2)

Required Tools and Adhesives

• Hobby knife
• Phillips screwdriver (small)

Note

: The stopper provided with the Twist™

has three holes that are not bored completely
through the stopper. The holes are for the
fuel pickup, fill and vent lines. For these
instructions, only two holes will be used: one
for the fuel pickup and one for the fuel vent.

Only open the third hole if you are going to
use a separate fill line.

Step 1

Locate the fuel tank parts.

Summary of Contents for Twist 3D .40









































Reviews:

No comments