Hangar 9 Alpha 40 Assembly Manual Download Page 46

Page: 46 / 48

Non-Warranty Repairs

Should your repair not be covered by warranty the repair

will be completed and payment will be required without

notification or estimate of the expense unless the expense

exceeds 50% of the retail purchase cost.

By submitting the item

for repair you are agreeing to payment of the repair without notification.

Repair estimates are available upon request. You must include this

request with your repair. Non-warranty repair estimates will be billed

a minimum of ½ hour of labor. In addition you will be billed for return

freight. Horizon accepts money orders and cashiers checks,

as well as Visa, MasterCard, American Express, and Discover cards.

By submitting any item to Horizon for inspection or repair, you are

agreeing to Horizon’s Terms and Conditions found on our website

under the Repairs tab

Country of Purchase Horizon Hobby

Address

Phone Number/ Email

United States

Horizon Service Center
(Electronics and engines)

4105 Fieldstone Rd

Champaign, Illinois

61822 USA

877-504-0233
productsupport@horizonhobby.

com

Horizon Product Support
(All other products)

4105 Fieldstone Rd

Champaign, Illinois

61822 USA

877-504-0233
productsupport@horizonhobby.

com

United Kingdom

Horizon Hobby Limited

Units 1-4 Ployters Rd

Staple Tye

Harlow, Essex

CM18 7NS

United Kingdom

+44 (0) 1279 641 097
[email protected]

Germany

Horizon Technischer Service

Hamburger Str. 10

25335 Elmshorn

Germany

+49 4121 46199 66
[email protected]

France

Horizon Hobby SAS

14 Rue Gustave Eiffel

Zone d’Activité du Réveil

Matin

91230 Montgeron

+33 (0) 1 60 47 44 70

FCC Information

This device complies with part 15 of the FCC rules. Operation is

subject to the following two conditions: (1) This device may not cause

harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

Caution

: Changes or modifications not expressly approved by the

party responsible for compliance could void the user’s authority to

operate the equipment.

This product contains a radio transmitter with wireless technology

which has been tested and found to be compliant with the applicable

regulations governing a radio transmitter in the 2.400GHz to

2.4835GHz frequency range.

Antenna Separation Distance

When operating your Spektrum transmitter, please be sure to maintain

a separation distance of at least 5 cm between your body (excluding

fingers, hands, wrists, ankles and feet) and the antenna to meet RF

exposure safety requirements as determined by FCC regulations.

The following illustrations show the approximate 5 cm RF exposure

area and typical hand placement when operating your Spektrum

transmitter.

12843.1_HAN_Alpha40_SpektrumManual.indd 46

6/4/10 10:18:53 AM

Summary of Contents for Alpha 40

















































Search results

Summary of Contents for Alpha 40

Reviews:

Related manuals for Alpha 40

Brands by name

Popular brands

Hangar 9 Alpha 40, Assembly Manual

Search results

Summary of Contents for Alpha 40

Reviews:

Related manuals for Alpha 40

Brands by name

Popular brands