H&S 125 PTO Operator'S Manual Download Page 24 | Manualshive

Page: 24 / 30

background image

DECAL LOCATION

PART # QTY

DESCRIPTION

311

1

Patent Numbers

1494A

3

Warning - Do Not Operate

1494J

2

Warning - Do Not Clean

1494K

3

Warning - Do Not Remove Shields

1494L

1

Danger - Rotating Driveline (On PTO Shaft)

8384

1

H&S Logo Decal (Left)

8385

1

H&S Logo Decal (Right)

8386

1

H&S Logo Decal (Front)

9194A

1

Danger - No Step

9194B

1

Danger - Never Allow Riders

12794

1

Warning - Do Not Remove Shields

52703D

1

Beater Engage/Disengaged

54033

1

Made in USA

72203A

1

Warning - Help Avoid Injury

71494A

2

Warning - Do Not Operate

081312

1

Zerk Located Behind Sprocket

82602

1

Warning - Crushing Hazard

093466

1

540 RPM Maximum Rotating Speed (On PTO Shaft)

093020

6

Grease Zerk

7143189

1

Beater Disengaged - Clean Out

11211176

1

Shear Bolts

111593A

2

Danger - Stay Clear of Beater

DCRED

2

Red Reflector

66076

1

Zerk Located Behind Shield

Your H&S Manure Spreader was manufactured with operator safety in mind. Located on the Manure
Spreader are various decals to aid in operation, and warn of danger or caution areas. Pay close attention
to all decals on your Manure Spreader.

DO NOT REMOVE ANY OF THESE DECALS. IF THE DECALS ARE LOST, DAMAGED,
OR IF THE MANURE SPREADER IS REPAINTED, REPLACE THE DECALS.
REMEMBER: DECALS ARE FOR YOUR PROTECTION AND INFORMATION.

Listed below are the decals on your Manure Spreader. These decals may be ordered individually by part
number or by ordering a complete set.

-22-

«
...
22
23
24
25
26
...
»

Summary of Contents for 125 PTO































Reviews:

No comments

Related manuals for 125 PTO

VR4 S-MF Series

Brand: Vanderbilt Pages: 24

Brand: Stanley Pages: 20

Brand: H&S Pages: 34

Brand: Intuit Pages: 2

Brand: ZKTeco Pages: 6

Brand: Sigur Pages: 52

Brand: Icy Box Pages: 2

Brand: Icy Box Pages: 2

Brand: Icy Box Pages: 11

Brand: Icy Box Pages: 12

THINGMAGIC SARGAS

Brand: Jadac Pages: 59

Brand: Vauban Systems Pages: 20

Brand: Precision Pages: 2

Brand: Identive Pages: 2

Brand: Rauch Pages: 90

Brand: Dazzle Pages: 49

ARD-AYBS6 0 MIFARE Series

Brand: Bosch Pages: 24

Brand: Nedap Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands