Table 2
Ethernet Port Pinout
Connector
Pin
Signal
Name
PoE
1
2
3
4
5
6
7
8
1
PoE-
2
RJ45_DA–
PoE-
3
PoE+
4
PoE+
5
RJ45_DC–
PoE+
6
RJ45_DB–
PoE+
7
PoE-
8
RJ45_DD–
PoE-
Table 3
Console
Port Pinout
Connector
Pin
Signal Name
Function
1
2
3
4
5
6
7
8
3
TXD
Transmit
4
GND
Ground
5
GND
Ground
6
RXD
Receive
Pins not listed are not connected.
Table 4
RS-485 Port Pinout
Connector
Pin
Signal Name
Function
1
2
3
4
5
6
7
8
1
RS485_B
Data-
2
RS485_A
Data+
4
GND
Ground
5
GND
Ground
Pins not listed are not connected.
Note: The serial console port allows you to connect the AP to a
serial terminal or a laptop for direct local management. This port
is an RJ-45 female connector with the pinouts described in Table 3.
Currently for use by Service & Support only.
Note: The RS-485 port allows you to connect the AP to a RS-485
terminal. The maximum allowable current of PSE 12V power output
is 300mA. In addition, PSE 12V power output can be turned on and
off by software. This port is an RJ-45 female connector with the
pinouts described in Table 4.
Power
The AP301 series access point supports direct DC power adapter (48V
DC nominal, sold separately) and Power over Ethernet (PoE).
The DC power connector port is located on the back of the device, as
shown in Figure 3.
The PoE allows the Ethernet port to draw power from an IEEE
802.3at compliant source.
HAN Access Point supports the power adapter provided by HAN ONLY.
Before You Begin
Refer to the sections below before beginning the installation process.
Pre-installation Checklist
Before installing your
AP301 Stellar access
point, be sure that you
have the following items:
•
8-conductor, CAT5 or better UTP cable of required length.
•
One of the following power sources:
◼
IEEE 802.3at compliant Power over Ethernet (PoE) source
(PoE switch or PoE injector).
◼
AC-DC adapter (sold separately)
，
output voltage DC 48V,
output current
≥
0.6A
•
A terminal or a notebook
Identifying Specific Installation Locations
You can mount the
HAN Access Points
on a ceiling rail
or on a wall
.
You should first determine the location of the installation. The
installation position is located at the center of the required
coverage area and should be free from obstructions or obvious
sources of interference.
•
Minimize the number of obstructions (such as walls) between the
AP and user terminals.
•
Electronic equipment or devices (such as microwave ovens) which
may produce radio frequency noise should be away from the
installation position of the AP.
It is strictly prohibited to install around stagnant water, water seepage,
leakage or condensation. Avoid cable condensation or water seepage
along the cables connecting to the AP.
AP Installation
Refer to mounting kits installation Guide.
Verifying Post-Installation Connectivity
The LED on the AP can be used to verify that the AP is receiving power
and initializing successfully.
Product Specifications
AP301 series Dimensions/Weight
Unboxed AP301:
•
Net Weight: 1.64lbs / 0.74kg
•
Dimensions (HxWxD): 7.1 inches x 7.1 inches x 1.42 inches
(18 cm x 18cm x 3.6cm)
Environmental
•
Operating :
▪
Temperature: 0°C to +50°C (+32°F to +122°F)
▪
Humidity: 10% to 90% non-condensing
•
Storage and transportation :
▪
Temperature: -40°C to +70°C(-40°F to +158°F)
For additional specifications on this product, please refer to the
Datasheet.
