©1999 Hamtronics, Inc.; Hilton NY; USA. All rights reserved. Hamtronics is a registered trademark. Revised: 5/3/04
- Page 1 -
CONSTRUCTION.
a. Set heatsink on bench. Note
where PA transistor is to be mounted
to two adjacent holes. Align the pc
board with the heatsink, matching the
cutout for the transistor and the pc
board mounting holes with the holes
on the heatsink.
Note that the heat-
sink is used for several products; so
there may be extra which are not used
in this model.
b. Temporarily remove the pc
board, and set two #8 flat washers
over each of the four mounting holes
on the heatsink to use as spacers.
The two washers provide the proper
thickness for the pc board spacing
needed for the transistor. Be sure to
use the ones supplied to prevent dam-
age to the transistor.
Set the pc board
in place, and secure with four each 6-
32 x 3/8 inch thread cutting screws.
The screws go through the pc board
and spacer washers and thread into
the aluminum heatsink.
Be careful
not to over tighten the screws and strip
the threads.
c.
Locate the power transistor, and
note that the collector lead is the nar-
row one (see component location dia-
gram). The collector lead should face
the right-hand side (toward connec-
tors). Apply a small amount of
heatsink compound to the bottom
surface of the transistor, and set it in
place through the cutout in the board.
d. Secure the transistor with two
4-40 x ½ inch screws inserted
through the transistor flange into the
heatsink. Use lockwashers and nuts
on the fin side of the heatsink. Align
the transistor with the board before
tightening screws.
Refer to the pc board component lo-
cation diagram in the rear of the man-
ual for the following assembly opera-
tions.
e. Solder the six transistor leads
to the pc board. It is important to
solder the entire surface of each lead
and use enough solder to form a bond
under the leads.
f. Install the metal clad mica ca-
pacitors in the exact positions shown.
The flat side with the value markings
should be up. Bend the tabs down so
they just touch the board with the
case flat against the board. Hold each
capacitor in place and solder the tab
to the board; then, solder each side of
the metal case to the ground plane.
C6, C7, C15, and C16 should be over
the emitter leads.
g. Solder C11, C12, and C13 in
place as shown. The .01uF capacitor
may be marked "103". The 0.15 uF
mylar capacitor is red. Observe polar-
ity of electrolytic capacitor C13.
h. Install variable mica capacitors
C1-C3, and C8 as shown, and solder
them in the exact positions shown,
which leaves room for the coils. The
leads need not be bent; they will stand
up on the board as is.
i. Form hairpin coils L1-L3 as
shown in the component location dia-
gram, using #14 bus wire supplied.
Coils are soldered with the feet (see
detail) flat against the board.
j. Ferrite chokes Z1-Z3 are 6-hole
balun cores with 2½ turns of #22 bus
wire threaded through the holes in the
manner shown in the detail. The
turns go only through the holes, not
around the outside of the core, except
at the ends. Cut a 3-inch length of
wire. Feed it through a hole with
about ½ inch protruding, and hold
this short end. Then, thread the long
end through the adjacent hole and
pull tight. Thread through a third
hole as shown until 2½ turns are
complete. (One hole is not used.)
Tack solder the leads of the balun
chokes to the board in the positions
shown.
k. Solder the two resistors in place
with short leads. R1 goes from the
base of Q1 to ground, positioned as
shown. R2 goes across balun choke
Z2.
l. Solder a length of hookup wire
to the pad by C10 to p13.6
Vdc operating power when the unit is
used.
m. Coax cables for the input and
output are soldered directly to the
board. Strip a length of 50 ohm coax
and solder to input of board. Keep
stripped lead lengths to no more than
1/4 inch to avoid losses. The center
lead at the pc board must be con-
nected at the very end of the stripline
as shown.
n. Solder another piece of coax to
the output of the board as shown.
o. Check to be sure all parts have
been installed. Check for potential
short circuits and other workmanship
problems. Double check circuit to
schematic diagram.
ALIGNMENT
a. Preset the variable capacitors
about 1½ turns ccw from fully tight.
b. Connect RF Input to repeater
output or other source of 15 Watts
drive. Connect RF Output through
power meter to a good 50
Ω
vhf
dummy load.
c. Connect reg13.6Vdc
power source to dc input wire and
power supply ground to ground plane
on board. (If your power supply has
adjustable voltage, it is better to start
tuning with about 10Vdc and increase
it to 13.6 Vdc after you determine
there are no problems.)
Note: Do not retune repeater output
stage or other driving source with PA
HAMTRONICS
RPA-402 220 MHZ REPEATER POWER AMPLIFIER
ASSEMBLY, OPERATION, & MAINTENANCE INSTRUCTIONS
Mounting Screws
Hole Not Used
Figure 1. Bottom View of Heatsink